Source Technologies 1352 MICR 40 manual Printer Installation

Page 5

Section 1: Printer Installation

1 Printer Installation

For complete information on how to unpack and setup your printer, see your printer’s user’s guide. Please read the following if you are going to install the printer driver shipped with your printer.

1. Locate the CD that was shipped with your printer.

Note: If you do not have a CD-ROM drive on the host PC, locate another computer with a CD-ROM drive, start the CD-ROM utility, and then follow the instructions on the screen to create printer driver diskettes.

2.Follow the instructions in the CD booklet to start the printer setup utility appropriate for your operating system, i.e. Windows 95, NT, etc. The setup utility will install printer driver and utilities to manage Source Technologies printer(s) attached to your PC or Network.

3.The Source Technologies, in most cases, assumes the printer driver

is set to the internal DEFAULT values. The following Default values should not be changed for best overall printer performance and data stream requirements of the ST Secure MICR printer.

-Print Resolution under the Graphic Tab should be set to the Default value of 600 DPI.

-Form Source under the Paper Tab should be set to Default value of By Source.

-Print Quality and PictureGrade under the Graphic Tab should be set to the Default values of Use Printer Default.

The ST Secure MICR Printer requires a PCL5 or PCL5e data stream. Current level printer drivers require Graphic Mode under the Graphic Tab be set to either Raster or GL/2. We recommend Raster. This is the only required non-Default value that needs to be set in the printer driver.

A majority of other driver options can be set for your particular requirements. The most obvious of these would be a Paper Tray selection if your application uses the Print Driver Setting.

Secure MICR Printer User’s Guide July 2003

Page 1	© Source Technologies
	All rights reserved

Image 5

Contents IBM Infoprint 1352 Micr Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error MessagesPrinter Installation Micr Printing Today Micr OverviewCheck Processing System Micr Overview Position and Dimension Gauge General Features of Check DesignMicr Check Design Design Elements in Detail PaperMicr Clear Band DuplexingData Elements Date Amount Convenience AmountDollars Amount In WordsPayee Area Signature AreaCheck Serial Number Fractional Routing Number Micr Line Account Title Memo LineAuxiliary On-Us Field Positions 65 to External Processing Code EPC Field PositionOn-Us Field Positions 32 to Routing Field Positions 43 toSample Check Quality Issues Micr Check Stock WeightQuality LayoutMoisture Check Stock Security Features Security IssuesSecurity Note Security Issues Micr Mode Micr FeaturesMicr Fonts Secure FontsResource Storage Bi-Directional Feedback@PJL Ustatus Device Micr Menu STH Command Entering Micr ModeSTF Command Micr Definition Command SMCPxxxx$ optional PasswordSet New Password Command &%STExxxxxxxx$ SmcpPrint Micr E-13B Font SMDddd...ddd$ STSSMD Print Micr CMC7 Font SM7ddd...ddd$Print ICR Secure Numeric Font &%SMIxxxxxx~ Print Secure Numeric Font SMFddd..ddd~Print MicroPrint Line SMMxxxxxxxxx!$ Load Flash Resource STLxxxxxyyyyyyzdd....ddTray Lock Command STTL#$ Secure Flash Resource Unlock Command STPxxxxx$Tray Unlock Command STTU#$ Tray Swapping CommandsDES and AES Decryption STDON$ Customer Character Conversation Command Special Alert and Custom Beep Command Hex Transfer IBM Host Programming Features and ExamplesTurning Hex Transfer On Turning Hex Transfer OffHex Transfer Examples Micr Mode Command Example NON-NEGOTIABLE STFPASSWORD$ Commands in .1 in order of appearanceSTY4040$ Escape Character TranslationSTY4000$ Example &%STY2300$Audit Trail Reports Print Audit Report End Audit Record Audit Trail Report Command SetAudit Report Field One SQ1d..d$ Audit Report Field Two-MICR Line SMDd..d$ or &%SM7d..d$Audit Report Field Five SQ5d..d$ Audit Report Field Four SQ4d..d~Audit Report Field Six SQ6d..d$ Audit Report Field Seven SQ7d..d$Spurge Print and Purge Audit Report &%SPURGExx$Print Audit Report SPRINTxx$ SprintSQ4 Start Audit Feedback CommandSQ5 SQ6Audit Trail Commands Example Void SAR$ Command terminatorSQ1200$200 SQ6October 5, 2005$SQ7103345 AM$ SMD...$Msmith See list of Micr Error Messages on following Error MessagesError Message On Display Printed Message Description Action Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$Appendix B CMC7 Micr Font Mapping Command SM7ddd..ddd$Appendix C Secure Numeric Font Mapping Command SMFddd...dd~Example &%SMF$1,123.00~ Will print Appendix D ICR Secure Numeric Font Mapping Command SMIxxxxxx~Description Command Appendix E Micr Mode Command SummaryDescription Command Structure Function Appendix F Audit Report Command SummaryFonts and Secured Resources Appendix G PJL Based Micr CommandsPJL Unlock Sequence PJL Re-Lock SequencePCL Font Call Commands PJL Re-Lock Sequence With a New Password ValuePJL Info Micr Command Cartridge Status = Unknown PCL Macro Call PCL Initial Set-UpPCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check @PJL Enter Language = PCL PJL and PCL commands used to print the sample check