Acer 500L IDE Primary Channel Slave, IDE Secondary Channel Master, IDE Secondary Channel Slave

Page 58

IDE Primary Channel Slave

This parameter lets you configure the hard disk drive connected to the slave port of IDE channel 1.

IDE Secondary Channel Master

This parameter lets you configure the hard disk drive connected to the master port of IDE channel 2.

IDE Secondary Channel Slave

This parameter lets you configure the hard disk drive connected to the slave port of IDE channel 2.

The following screen appears if you select any of the IDE Drive parameters:

IDE Primary/Secondary
Channel Master/Slave

Type	[ Auto ]
Cylinder	[ XXXX ]
Head	[ XXXX ]
Sector	[ XXXX ]
Size	[ XXXX ] MB
Hard Disk Size > 504MB	[ Auto ]
*Hard Disk Block Mode	[ Auto ]
*Advanced PIO Mode	[ Auto ]
*Hard Disk 32-bit Access	[Enabled ]
*DMA Transfer Mode	[Auto]
*CD-ROM Drive DMA Mode	[Disabled]

The above parameters marked with ‘*’ will only appear if you access the advanced configuration level in the Main Menu. Please refer to the Entering Setup section at the beginning of this chapter for more information.

Type

3-12	AcerAltos 500L User’s Guide

Image 58

Contents AcerAltos 500L Copyright Important Safety Instructions Page Page FCC Class B Radio Frequency Interference Statement Getting Started Conventions Table of Contents Bios Utility Page Xii System Housing Standalone SystemFeatures Front PanelRear Panel Internal Structure Opening the Housing Panels Left Panel Installing Disk Drives Inch Floppy DriveInch Drives Hard Disk Drives Installing Expansion Cards System Housing Page System Board Major Components System Board Layout Jumpers and Connectors Jumper and Connector LocationsJumper Settings Connector FunctionsPower switch ESD Precautions Installing the Pentium II Processor Attaching the Processor Fan SinkSystem Board AcerAltos 500L User’s Guide Installing a Pentium II Processor AcerAltos 500L User’s Guide Removing a Pentium II Processor AcerAltos 500L User’s Guide Memory Upgrade Memory ConfigurationsInstalling a Dimm Removing a Dimm Reconfiguring the System Software Error Messages Error MessagesSystem Error Messages Mmmmssssooo Wxxxx System Board Correcting Error Conditions Bios Utility Entering Setup Setup UtilityBios Utility System Information Internal Cache Size ProcessorProcessor Speed External CacheIDE Secondary Channel Master IDE Primary Channel MasterIDE Primary Channel Slave IDE Secondary Channel SlaveParallel Port Serial PortPS/2 Mouse System S/N Product InformationProduct Name Main Board IDDMI Bios Version System Bios VersionMain Board S/N Disk Drives Floppy DrivesIDE Drives LS-120 Drive Compatible AsIDE Primary Channel Master IDE Secondary Channel Master IDE Primary Channel SlaveIDE Secondary Channel Slave Enhanced IDE Features Hard Disk Block Mode Bios Utility Serial Ports 1 Onboard PeripheralsBase Address Operation Mode 3BCh 378hOnboard Device Settings EPPPS/2 Mouse Controller Floppy Disk ControllerIDE Controller USB Host ControllerSMBus Interrupt IRQ9 Power Management Mode Power ManagementIDE Hard Disk Standby Timer Modem Ring Indicator Power Switch 4 secSystem Sleep Timer System Wake-up EventBoot Options Boot SequenceSilent Boot Fast BootFirst Hard Disk Drive Boot from LANDesk Service Agent Num Lock After BootConfiguration Table Memory TestDate and Time DateTime To set or change a Password Setup PasswordSystem Security Set or Change Password To remove your Setup Password Power-on Password To bypass Setup PasswordPower-on Password Disk Drive ControlBios Utility Advanced Options Memory/Cache OptionsExternal Cache Internal Cache CPU CacheMemory at 15MB-16MB Reserved for PCI IRQ Setting Memory Parity ModePnP/PCI Options PCI IRQ Sharing VGA Palette SnoopGraphics Aperture Size Reset Resource AssignmentsCPU Frequency Plug and Play OSCPU Multiple Bus FrequencyProcessor Speed Load Default Settings Abort Settings Change Exit Setup SCSI/VGA Combo Card Page LCD Module Event Log List