Acer 500L manual System Board

Page 45

	Message		Action
	Memory Size Mismatch	Check the memory size based on
	CPU Clock Mismatch	the system specifications. Check
	CPU Clock Mismatch	the internal cable connections. If
		the internal cable connections. If
		you are sure that connections and
		values are correct, ignore the
		message. If the message
		reappears, ask for technical
		assistance.

	Onboard Serial Port 1 Conflict	Run Setup and disable the port.

	Onboard Serial Port 2 Conflict	Run Setup and disable the port.

	Onboard Parallel Port Conflict	Run Setup and disable the port.

	Pointing Device Error	Check and connect pointing
		device.

	Pointing Device Interface	Replace the pointing device or
	Error	contact your dealer.

	Press F1 key to continue or	Press	or
	Ctrl-Alt-Esc for Setup	+	+	to enter
		Setup.

	Real Time Clock Error	Run Setup and set the time and
		date.

	Press Esc to turn off NMI, any	Press	to disregard the NMI
	key to reboot	error.
		Press any other key to reboot the
		system.

Chapter 2 System Board

2-21

Image 45

Contents AcerAltos 500L Copyright Important Safety Instructions Page Page FCC Class B Radio Frequency Interference Statement Getting Started Conventions Table of Contents Bios Utility Page Xii Standalone System System HousingFront Panel FeaturesRear Panel Internal Structure Opening the Housing Panels Left Panel Inch Floppy Drive Installing Disk DrivesInch Drives Hard Disk Drives Installing Expansion Cards System Housing Page System Board Major Components System Board Layout Jumper and Connector Locations Jumpers and ConnectorsConnector Functions Jumper SettingsPower switch ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II ProcessorSystem Board AcerAltos 500L User’s Guide Installing a Pentium II Processor AcerAltos 500L User’s Guide Removing a Pentium II Processor AcerAltos 500L User’s Guide Memory Configurations Memory UpgradeInstalling a Dimm Removing a Dimm Reconfiguring the System Error Messages Software Error MessagesSystem Error Messages Mmmmssssooo Wxxxx System Board Correcting Error Conditions Bios Utility Setup Utility Entering SetupBios Utility System Information Processor Speed ProcessorInternal Cache Size External CacheIDE Primary Channel Slave IDE Primary Channel MasterIDE Secondary Channel Master IDE Secondary Channel SlaveSerial Port Parallel PortPS/2 Mouse Product Name Product InformationSystem S/N Main Board IDSystem Bios Version DMI Bios VersionMain Board S/N Floppy Drives Disk DrivesLS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave Enhanced IDE Features Hard Disk Block Mode Bios Utility Onboard Peripherals Serial Ports 1Base Address 3BCh 378h Operation ModeEPP Onboard Device SettingsIDE Controller Floppy Disk ControllerPS/2 Mouse Controller USB Host ControllerSMBus Interrupt IRQ9 Power Management Power Management ModeIDE Hard Disk Standby Timer System Sleep Timer Power Switch 4 secModem Ring Indicator System Wake-up EventBoot Sequence Boot OptionsFast Boot Silent BootFirst Hard Disk Drive Configuration Table Num Lock After BootBoot from LANDesk Service Agent Memory TestDate Date and TimeTime Setup Password To set or change a PasswordSystem Security Set or Change Password To remove your Setup Password To bypass Setup Password Power-on PasswordDisk Drive Control Power-on PasswordBios Utility Memory/Cache Options Advanced OptionsInternal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode PCI IRQ SettingPnP/PCI Options VGA Palette Snoop PCI IRQ SharingCPU Frequency Reset Resource AssignmentsGraphics Aperture Size Plug and Play OSBus Frequency CPU MultipleProcessor Speed Load Default Settings Abort Settings Change Exit Setup SCSI/VGA Combo Card Page LCD Module Event Log List