Motorola BC796D, APCO25 manual FCC Wants You To Know

Page 7

The FCC Wants You To Know

This scanner has been tested and found to comply with the limits for a scanning receiver, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This scanner generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this scanner does cause harmful interference to radio or television reception, which can be determined by turning the scanner on and off, you are encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the scanner and the receiver

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

1

Image 7

Contents Page Page Contents General Programming Setting Apco 25 Sound Quality Programming LTR Systems Page FCC Wants You To Know Scanning Legally Introduction Page Using this Manual Repeater Operation Understanding ScanningConventional Scanning Simplex OperationMotorola Trunking Trunked ScanningEdacs Trunking LTR Trunking Understanding Banks and ChannelsGetting More Information BC796D Front and Rear ViewIcon Description Display IconsIncluded With Your Scanner Optional Antenna Setting Up Your ScannerConnecting an Antenna Mounting an AntennaMounting the Scanner in Your Vehicle Typical Mounting MethodsApplying Power for Vehicle Installation Connecting an Earphone Desktop InstallationApplying Power Using Standard AC Power Connecting an External SpeakerRemember Connecting the Clone CableConnecting the Tape Recorder Listening SafelyBasic Operation Setting the SquelchTurning On the Scanner Locking/Unlocking Banks Using the MenuManually Selecting a Channel Scanning Programmed ChannelsPriority Plus Scanning Locking/Unlocking ChannelsRestoring All Locked Out Channels Priority ScanningLocking the Enter key Dimmer Light SettingControlling How Much Information Appears Turning the Key Beep On/OffTrunk Scanning Options Setting Squelch ModeDisabling the APCO25 Card Muting All AudioHolding on a Single Talkgroup Scanning Only Stored Talkgroups ID ScanMonitoring Talkgroup ID’s Selecting Talkgroup Lists to ScanUnlocking All Talkgroups Edacs BlockoutEdacs Patch Tracking Holding on an Active Frequency Setting Chain SearchSetting Data Skip SearchingAutomatically Storing Frequencies Storing Found FrequenciesAttenuating All Search Ranges Setting Subaudible Tones for SearchingSetting Delay for All Search Ranges Searching for Subaudible TonesSearching for Trunk Systems Setting a Search RangePage Service Search Skip Service SearchUsing Weather Alert Same Using Weather Search and Weather Alert SameSearching for a Weather Broadcast Testing the Weather Alert Programming Bank Information Bank ConfigurationAssigning Bank Names Entering Alpha Information General ProgrammingDeleting Frequencies from Channels Transferring Channel InformationPage Assigning a Text Tag Programming Conventional ChannelsSelect a Channel to Program Enter the FrequencySetting the Subaudible Tone Option Setting the DelaySetting the Attenuator Setting Beep AlertChanging the Frequency Step Setting Priority Channels Setting the Modulation ModeProgramming Trunked Systems Using I-Call Motorola and Edacs only Setting Trunking DelayTurning I-Call On and Off for ID Search Multi-Track Operational Details Setting Priority Talkgroups Motorola and Edacs onlyMulti-Track Turning I-Call On for ID ScanPage Programming Motorola Systems Using Control Channel ProgrammingProgramming Type 2/Digital 800 and 900 MHz Systems Programming Type2/Digital VHF and UHF Systems Programming Type I and IIi Hybrid Systems Toggling End Code Detect Toggling the Status BitProgramming Edacs Systems Setting Edacs Emergency AlertProgramming Edacs Channels Setting Edacs Decimal Mode Programming Apco 25 Systems Setting Apco 25 Sound QualityProgramming LTR Systems Storing Known Talkgroups Programming TalkgroupsStoring Found Talkgroups Adding a Text Tag to an ID List Deleting Stored Talkgroup ID’sSeeing Talkgroup Activity PC Control Mode Using the Remote InterfaceCloning Scanner Settings Clone Master Unit Slave Unit Care and Maintenance Troubleshooting Problem Suggestion Specifications Glossary of Terms Page Page Appendix Preset Fleet MapsPreset Map Block Type I Programming Information User Defined Fleet MapsSize Code Restrictions Fleet Map Size CodesNWR-SAME Event Code SVS Severe WX Reverse List BC796D Flow Charts Beep Alert System Option Dimmer Uniden America Corporation One Year Limited WarrantyMemo Memo Memo