Mitsubishi Electronics HC6000 user manual Preparing your projector, Checking accessories

Page 6

Preparing your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

„ Cables

Mini D-SUB

15-pin

Mini D-SUB

15-pin

RGB cable for PC

(246C521-10)

D-SUB

9-pin

D-SUB

9-pin

RS-232C cable

(246C548-10)

Used for projector control by computer.

„Power supply parts

Power cord (two)

(246C483-10, 246C383-20)

„Remote control parts

Remote control

R6P (Size-AA)

(290P158-10)

battery (two)

„Filter parts

Accessory air-filter unit

(761B504-10)

„Others

Lens cap (attached to the projector)

Lamp replacement tray (857C106-10)

User Manual/Quick Start up (English only) (871D494-50)

CD-ROM (with User Manual) (919C154-50)

Safety Manual/Quick Start up (871D489-50)

Important:

• The attached power cords are to be used exclusively for this product. Never use them for other products.

Inserting the batteries into the remote control

1

 

1.

Remove the back lid of the remote control.

3

2.

Check the polarity (+), (-) of the batteries, and set them

 

 

 

correctly, inserting their (-) side first.

 

 

 

• If the battery is inserted from the (+) side first, inserting

 

 

 

the (-) side is difficult because the coil spring end hits

 

2

 

on the battery side. If the battery is forced in this way,

 

 

the outer label of the battery may get ripped and it may

 

 

 

cause a short-circuit and heating.

 

 

3.

Attach the back lid.

 

 

Important:

 

 

Use two size-AA batteries (R6P).

 

 

Replace the two batteries with new ones when the remote

 

 

 

control is slow to respond.

Caution:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or throw them in fire.

Be sure to handle the batteries according to the instructions.

Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the batteries, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Image 6
Contents HC6000 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Control area Preparing your projectorOverview Terminal panelAdjustment feet Remote controlUsing the picture quality adjusting buttons Bottom sideReception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Lens Shift buttonWhen fine streaks are seen on projected images Setting up your projectorAdjusting the projection angle When projected images are distorted to a trapezoidWhen the aspect ratio of the screen is When the aspect ratio of the image isScreen size and projection distance Rear projection With the Installation menu See page 26 for menu settingFront projection, ceiling mounting Trigger terminalBasic home theater system connection Connecting the projector to video equipmentViewing video images PreparationWhen a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesConnecting to video equipment having a Hdmi terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images To stop projecting Setting the aspect ratio ZOOM1 ZOOM2 StretchHow to change the settings With the remote controlWith the Feature menu See page 26 for menu setting Viewing computer images Connecting the projector to a computerPlugging the power cord About DDCViewing computer images ComputerWhen connecting to a notebook computer Example of the setting procedure for external outputAuto Position button Menu operation Contrast BMenu operation How to set the menusAvailable settings in the menus Image menuInstallation menu Feature menu Signal menu User menuAV memory To store the settingsTo enable the stored image quality settings Information menuTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp To enable the stored color temperatureTo adjust the ratio of change in brightness Gamma Mode Noise reductionTo adjust the vertical position LPFTo enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampReplacing the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector To replace the lampCleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensCleaning the air-filter Accessory air-filter unitAttaching the accessory air-filter unit For the air-filter whiteTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution Normal condition IndicatorsStatus Condition Possible Solution Abnormal conditionDimension drawings unit mm SpecificationsSpecifications Computer IN/COMPONENT Video Hdmi ConnectorsReplacement part Option/not included in the box VLT-HC5000LPMitsubishi Projector Contact Information
Related manuals
Manual 7 pages 37.62 Kb