Panasonic DP-180 appendix For U.K, And-Yellow, Black

Page 12

Getting To Know Your Machine

Precautions

Installation

For U.K.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR OFFICE

THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green and Yellow : Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the main lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by letter E or by the safety Earth symbol “ “ or coloured GREEN or GREEN-

AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse.

Open the fuse compartment with a screwdriver and replace the fuse.

Handling

Do not turn the Power Switch Off or open the Front Cover during copying/printing.

Energy Saver Mode Notice

The following functions will not work if the Energy Saver Mode setting is set to the Shutdown mode.

When using any of the following functions, we recommend that you leave the Energy Saver Mode in the initial factory default setting (Sleep mode). (See page 36)

Printer Function (USB Local and Network Connections)

Internet Fax/Email Function

Facsimile Function

When the LAN cable is not connect and DHCP DEFAULT is "VALID" (See page 37)

12

Image 12
Contents Function Problem Solving Network Scanner EnglishMaking Copies Before Starting Useful Office Functions Multi-Tasking Job TableOperating Instructions Outline Symbols/Icons Place originals on the ADFTable of Contents Getting to Know Your Machine FunctionTable of Contents Network Scanner Problem SolvingAppendix Precautions Laser SafetyFor Your Safety Others Consumable Safeguards Supplies It is unlawful to make copies of certain documentsFor U.K AND-YELLOWBlack Procedures Original PositionHole Cover Operation Chart Quick Operation ChartBefore Pressing Start Key Making CopiesReplacing Toner Cartridge and/or Drum Unit Cleaner To replace the Toner CartridgeTo replace the Drum Unit For replacing the Toner Cartridge onlyJ44, J82, J83 J43, J44, J80Removing Misfed Paper ADF J70, J71, J79, J90, J92, J93 Front Cover Misfed Paper Paper Transport KnobUser Error Codes U Code Jam Error Codes J CodeCode Check Points CorrectIncorrect Adding Paper / Sheet BypassAdding Paper / Tray-2 Icon Contents Memory in key Color Key Resolution Key Original Size KeyM1 Key Original KeyIcon Contents Reset Key Alarm LED RED Lights/Flashes when trouble occursIcon Contents Keypad Sets copy quantities or Function settingsSort Mode Copying with Preset or Variable Zoom RatiosBasic Copy Copying the Same Size OriginalsUsing the ADF Creative Features CopyCopy, 2 1 Copy Exits this mode FromPlaten only For 2 1 CopyMode Originals Layout 1 CopyCombination for N in 1 copy operation AvailableFor Preset Ratios A4 A4-R A5 A5-R Steps 7 to 11 from Platen onlyOther Features Skyshot ModeDigital Skyshot Mode Double Exposure4- 2 to step Starts making copies A4 A4-R A5 A5 A5-REnergy Saver Power Saver Mode, Sleep/Shutdown Mode Power Saver ModeSleep/Shutdown Mode Set up Job MemoryTo store a job in memory To recall a job stored in memoryUsing Function Modes to Change the Initial Machine Modes ProcedureGeneral Settings Printer SettingsCopier Settings When selecting the Key Operator Mode Ex. General SettingsGeneral Settings Modes Function Initial Setting1INVALID / 2VALID DEPT. Counter Mode Dhcp DefaultORIG. SET Beep ADF 2VALIDCopier Settings Printer Settings 1LONG Edge / 2SHORT Edge Resolution Symbol Table PCLPrinter Settings Sided PrintScanner Settings Scan Parameters If set in other function mode For ExampleChanging the Paper Size Paper Tray Changing the Paper Size Sheet BypassSelect Paper Size For LETTER/A4Others Network Settings Department CounterFor Department Counter For Maximum Copies For ID Identification CodeSET 19 TCP/IP AddressDocument Scanning Document Scanning23-3 Select a Station PCs IP Address AbbrName SearchAddress Book Adding your PCs IP AddressEditing/Erasing your PCs IP Address Enter a Station Name Select Mode Scan ParametersFor Scan File Name For CompressionFor Gray Scale Remote Copy Remote CopyNetwork Remote Copy NO. of COPY= Direct Connection with Crossover Cable Direct Connection with Crossover CableMachine Rear Side of Machine To PCFor Windows For Windows XPSubnet Mask Troubleshooting Check ActionUnit Does Not Operate Light CopiesMachine Care Marked CopiesSheet Platen glassReplacing the Battery/Set the Date and Time Battery HolderSet the Date and Time continues steps 6 to Used NewSpecifications DP-180 For CopierADF Standard FLSNetwork Scanner Standard 2nd Paper Feed Module DA-DS188 OptionCombined Function Table Next SelectionsOptions and Supplies OptionsSupplies Part Name RemarksImportant Information Energy Star For Service, Call