Panasonic DP-180 appendix Others

Page 9

Your Machine

Getting To Know

Never touch a power cord with wet hands. Danger of electric shock exists.

If the power cord is broken or insulated wires are exposed, contact your Service Provider for a replacement. Using a damaged cord can cause fire or electric shocks.

Stop operation immediately if your machine produces smoke, excessive heat, unusual noise, or smell, or if water is spilt onto the machine. These conditions can cause fire. Immediately switch Off and unplug the machine, and contact your Service Provider.

Do not disconnect or reconnect the machine while it is on. Disconnecting a live connector can deform the plug and cause fire.

When disconnecting the machine, grasp the plug instead of the cord. Forcibly pulling on a cord can damage it and cause fire or electric shock.

When the machine is not used over an extended period of time, switch it Off and unplug it. If an unused machine is left connected to a power source for a long period, degraded insulation can cause electric shocks, current leakage or fire.

Be sure to switch Off and unplug the machine before accessing the interior of the machine for cleaning, maintenance or fault clearance. Access to a live machine’s interior can cause electric shock.

Be sure to switch Off and unplug the machine before accessing the interior of the machine for accessing interface cables, maintenance or fault clearance. Access to a live machine’s interior can cause electric shock.

Once a month, unplug the machine and check the power cord for the following. If you notice any unusual condition, contact your Service Provider.

●The power cord is plugged firmly into the receptacle.

●The plug is not excessively heated, rusted, or bent.

●The plug and receptacle are free of dust.

●The cord is not cracked or frayed.

Others

■The machine has a built-in circuit for protection against lightning-induced surge current. If lightning strikes in your neighborhood, switch Off the machine. Disconnect the power cord from the machine and reconnect only when the lightning has stopped.

■If you notice flickering or distorted images or noises on your audio-visual units, your machine may be causing radio interference. Switch it Off and if the interference disappears, the machine is the cause of the radio interference. Perform the following procedure until the interference is corrected.

●Move the machine and the TV and/or radio away from each other.

●Reposition or reorient the machine and the TV and/or radio.

●Unplug the machine, TV and/or radio, and replug them into outlets that operate on different circuits.

●Reorient the TV and/or radio antennas and cables until the interference stops. For an outdoor antenna, ask your local electrician for support.

●Use a coaxial cable antenna.

Operating Safeguards

WARNING

Do not touch areas where these caution labels are attached to the surface as they may be very hot and cause severe burns.

Do not place any liquid container such as a vase or coffee cup on the machine. Spilt water can cause fire or shock hazard.

Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts get into the machine, they can short-circuit internal components, and cause fire or electric shocks.

If debris (metal or liquid) gets into the machine, switch Off and unplug the machine. Contact your

Service Provider. Operating a debris-contaminated machine can cause fire or electric shock.

Never open or remove machine covers that are secured with screws unless specifically instructed in the “Operating Instructions”. A high-voltage component can cause electric shocks.

Do not try to alter the machine configuration or modify any parts. An unauthorized modification can

cause smoke or fire.

9

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Function Problem Solving Network Scanner EnglishMaking Copies Before Starting Multi-Tasking Job Table Useful Office FunctionsOperating Instructions Outline Place originals on the ADF Symbols/IconsFunction Table of Contents Getting to Know Your MachineTable of Contents Network Scanner Problem SolvingAppendix Laser Safety PrecautionsFor Your Safety Others Consumable Safeguards It is unlawful to make copies of certain documents SuppliesFor U.K AND-YELLOWBlack Procedures Original PositionHole Cover Quick Operation Chart Operation ChartMaking Copies Before Pressing Start KeyReplacing Toner Cartridge and/or Drum Unit To replace the Toner Cartridge CleanerTo replace the Drum Unit For replacing the Toner Cartridge onlyJ44, J82, J83 J43, J44, J80Removing Misfed Paper ADF J70, J71, J79, J90, J92, J93 Paper Transport Knob Front Cover Misfed PaperUser Error Codes U Code Jam Error Codes J CodeCode Check Points CorrectIncorrect Adding Paper / Sheet BypassAdding Paper / Tray-2 Resolution Key Original Size Key Icon Contents Memory in key Color KeyM1 Key Original KeyAlarm LED RED Lights/Flashes when trouble occurs Icon Contents Reset KeyIcon Contents Keypad Sets copy quantities or Function settingsCopying with Preset or Variable Zoom Ratios Sort ModeBasic Copy Copying the Same Size OriginalsUsing the ADF Creative Features CopyCopy, 2 1 Copy From Exits this modePlaten only For 2 1 Copy1 Copy Mode Originals LayoutCombination for N in 1 copy operation AvailableSteps 7 to 11 from Platen only For Preset Ratios A4 A4-R A5 A5-RSkyshot Mode Other FeaturesDigital Skyshot Mode Double ExposureA4 A4-R A5 A5 A5-R 4- 2 to step Starts making copiesEnergy Saver Power Saver Mode, Sleep/Shutdown Mode Power Saver ModeSleep/Shutdown Mode Job Memory Set upTo store a job in memory To recall a job stored in memoryProcedure Using Function Modes to Change the Initial Machine ModesGeneral Settings Printer SettingsWhen selecting the Key Operator Mode Ex. General Settings Copier SettingsModes Function Initial Setting General SettingsDhcp Default 1INVALID / 2VALID DEPT. Counter ModeORIG. SET Beep ADF 2VALIDCopier Settings Printer Settings Symbol Table PCL 1LONG Edge / 2SHORT Edge ResolutionPrinter Settings Sided PrintScanner Settings Scan Parameters For Example If set in other function modeChanging the Paper Size Paper Tray Changing the Paper Size Sheet BypassSelect Paper Size For LETTER/A4Others Department Counter Network SettingsFor Department Counter For Maximum Copies For ID Identification Code19 TCP/IP Address SETDocument Scanning Document ScanningSelect a Station PCs IP Address Abbr 23-3Name SearchAddress Book Adding your PCs IP AddressEditing/Erasing your PCs IP Address Enter a Station Name Scan Parameters Select ModeFor Scan File Name For CompressionFor Gray Scale Remote Copy Remote CopyNetwork Remote Copy NO. of COPY= Direct Connection with Crossover Cable Direct Connection with Crossover CableMachine Rear Side of Machine To PCFor Windows For Windows XPSubnet Mask Check Action TroubleshootingUnit Does Not Operate Light CopiesMarked Copies Machine CareSheet Platen glassReplacing the Battery/Set the Date and Time Battery HolderSet the Date and Time continues steps 6 to New UsedDP-180 For Copier SpecificationsADF Standard FLS2nd Paper Feed Module DA-DS188 Option Network Scanner StandardCombined Function Table Next SelectionsOptions Options and SuppliesSupplies Part Name RemarksImportant Information Energy Star For Service, Call
Top Page Image Contents