Allied Telesis AT-2916LX10/LC-901, AT-2916SX, AT-2931SX, AT-2972T/2, AT-2972SX/2 manual

Page 69

AT-29xx Series Gigabit Ethernet Network Adapters Installation Guide

and allows the network adapter to wake up the system when an event, such as a ping or an ARP request, is received.

5. Click OK.

WOL Speed The WOL Speed property sets the speed at which the network adapter connects to the network while the adapter is in Wake on LAN (WOL) mode. On Windows 2008 R2, Windows Vista, and Windows 7 systems, the default speed for WOL mode is 100 Mb. This is the only speed available for an AT-29xx Series adapter running the Windows 2008 R2, Windows Vista, and Windows 7 operating systems.

The WOL speed is limited to 100 Mb due to power limitations on the PCI bus. The WOL feature is supported only on copper Gigabit NICs where the speed must be reduced from 1 Gb to 100 Mb for the NIC power consumption to be below the maximum power provided by the PCI bus.

On the Windows Server 2003 or Windows XP systems, this property is available on the AT-2972/T2 adapter only. By default, the WOL Speed property is set to Auto. However, there are several additional settings available.

To specify the WOL speed on a Windows Server 2003 or Windows XP system, perform the following procedure:

1.For Windows Server 2003 and Windows XP systems, access the System Properties Dialog Box. See “Modifying Configuration Properties” on page 39.

2.Click the Advanced tab.

The Advanced tab is shown in Figure 21 on page 56.

3.From the Properties list, select WOL Speed.

4.From the Values list, select one of the following:

ˆ10 Mb. Sets the speed to 10 Mbit/s. This is the network speed when the system is in a standby mode awaiting a wake-up frame.

ˆ100 Mb. Sets the speed to 100 Mbit/s.

ˆAuto (default). Sets the speed for optimum network connection.

5.Click OK.

6.If prompted to restart your computer, click Yes.

Although it is not necessary to reboot the system for new adapter properties to take effect, rebooting is recommended to reinitialize all registers.

69

Image 69
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Vlan ID Page Contents Figures Figures Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter Functional Description Contents of Your Shipment State Description LEDsAT-29xx Series Adapter Software Drivers Software Driver FeaturesFailover Teaming Installing the Hardware Reviewing Safety Precautions Page Pre-Installation Checklist Removing the PC Cover Installing a Network Adapter CardInstalling the Hardware Make sure the card is securely seated. See Figure Installing the Hardware Port Type Connector Media Maximum Distance Connecting the Network CablesWarranty Registration Chapter Using the Driver Installer Installing the Driver SoftwareClick Install from a list or specific location Advanced Click Include this location in the search Updating the Adapter Software Run Window Device Manager Window is shown in Figure Hardware Update Wizard Window Click Install from a list or specified location Advanced Modifying Configuration PropertiesPage Uninstalling the Driver Software Page Chapter Selecting the Device Manager in Windows 2008 R2 and Windows Selecting the Device ManagerPage Windows Vista Run Window Selecting the Device Manager in Windows VistaDevice Manager Window Installing Windows R2, Windows Vista, Driver Software Click Browse my computer for driver software Update Driver Software Ethernet Controller WindowUpdate Driver Software Confirmation Window Open the Device Manager Page Setting Advanced Properties Opening Advanced Properties Page Setting Advanced Properties Flow Control Ethernet@Wire- speed AT-2972/T2 onlySetting Advanced Properties Interrupt Moderation Setting Advanced Properties Large Send Offload Property Setting Advanced Properties Page Receive Side Scaling Speed & Duplex Mode Checksum Offload Page Wake Up Capabilities Page Setting Advanced Properties Installing the Linux Driver Software Installing the Linux Driver Software Building a Driver from a TAR FileRemoving the tg3 Driver Rmmod tg3 Network Installation Removing the Linux Driver from a TAR Installation Module Parameters ˆ linespeedˆ autospeed ˆ rxflowcontrol ˆ fullduplexˆ txflowcontrol ˆ autoflowcontrolˆ txchecksum ˆ mtuˆ rxchecksum ˆ scattergatherˆ rxjumbodesccnt ˆ adaptivecoalesceˆ rxcoalesceticks ˆ rxmaxcoalesceframes ˆ enablewolˆ txcoalesceticks ˆ txmaxcoalesceframesˆ enabletso Installing the Linux Driver Software Installing the Novell NetWare Driver Software Driver Installation NetWare OS Support Pack or Patch Files to be Installed Pre-Installation RequirementsSelect Save parameters and load driver to continue Installing Novell NetWare Server 5.x or 6.0 Driver SoftwarePage Verifying or Modifying Adapter Parameters Configuration Parameters for B57.LAN driverNODE= FRAME= Poll= Bind IPX B571E82 NET=FAFD3D25 Example Removing Drivers from Autoexec.ncfInstalling the Novell NetWare Driver Software Installing the NDIS2 Driver Software for MS-DOS Platforms Pre-Installation Requirements Change DriverName=$ to DriverName=B57$Example Protocol.ini for IP Example Protocol.ini for NetBEUI Example Protocol.ini for IPXExample SYSTEM.INI Change netcard= to netcard=b57.dosFor IPX Copy B57.dos to A\NetSET PATH=A\NET \NET\NET Start Basic For NetBEUIUsing Keywords for the B57.dos Drivers Page Installing the PXE Boot Agent Overview Windows Server 2003 Windows XP Server SetupInstalling the PXE Boot Agent 106 Troubleshooting Hardware Diagnostics Checking Port LEDs on the Adapter Troubleshooting Checklist Module Size Used by Verifying the Correct Drivers are LoadedTesting Network Connectivity Type ipconfig /allWindows Server Command Window with ping displayed 114 Windows XP Image Software Problems and Solutions116 DOS Diagnostics Introduction Command Description DOS Prompt CommandsGroup a Diagnostic TestsGroup B Group CA2. Control Register Test A1. Indirect Register TestA3. Interrupt Test A5. PCI Cfg Register TestB3. DMA Sram Test B2. BD Sram TestB4. Mbuf Sram Test B5. Mbuf Sram via DMA TestB6. External Sram Test Default DisabledC1. Eeprom Test C2. CPU TestC3. DMA Test C4. MII TestOffset Mask C6. ASF Test C5. VPD TestC7. ROM Expansion Test D1. Mac Loopback TestD2. Phy Loopback Test Function Default DisabledD3. RJ45 Loopback Test D4. MII Miscellaneous TestPass Error Messages128 129 130 Physical Specifications SpecificationsEnvironmental Specifications Appendix aPerformance Specifications Power SpecificationsOperating Specifications Appendix a Specifications 134 Appendix B Cleaning Fiber Optic ConnectorsRubbing the Ferrule Tip on the Cleaning Surface Using a Cartridge-Type Cleaner137 Cleaning a Recessed Ferrule If desired, repeat step Using a Swab139 Appendix B Cleaning Fiber Optic Connectors 140
Related manuals
Manual 102 pages 40.87 Kb Manual 2 pages 53.07 Kb Manual 82 pages 31.76 Kb

AT-2916LX10/LC-901, AT-2972SX, AT-2972SX/2, AT-2972LX10/LC-901, AT-2916SX specifications

The Allied Telesis AT-2972T/2 is a highly capable 10/100 Mbps Fast Ethernet switch designed to provide reliable performance and advanced management features for small to medium-sized businesses. This switch is built on a robust technology platform, making it an ideal choice for organizations looking to enhance their network infrastructure while ensuring scalability and flexibility.

One of the main features of the AT-2972T/2 is its support for 24 ports, allowing for extensive connectivity in a compact footprint. This makes it suitable for environments where space is limited but connectivity demands are high. With auto-negotiation on all ports, the switch automatically detects the best speed and duplex mode, ensuring optimal performance and seamless integration into existing networks.

The AT-2972T/2 incorporates advanced Layer 2 switching capabilities, enabling efficient handling of data traffic. Its ability to support VLAN (Virtual Local Area Network) tagging allows for network segmentation, improving performance and security. This feature is particularly beneficial for organizations that require different departments or teams to maintain their network traffic separately.

Quality of Service (QoS) is another significant aspect of the AT-2972T/2. The switch provides multiple traffic prioritization levels, ensuring that critical applications receive the necessary bandwidth to function effectively. This is essential in maintaining the performance of real-time applications such as VoIP and video conferencing, which are increasingly crucial in today’s business environment.

The built-in diagnostics features of the AT-2972T/2 enhance its reliability and ease of management. With capabilities such as loop detection and port mirroring, network administrators can quickly troubleshoot issues and monitor traffic flow to ensure a stable network.

Power over Ethernet (PoE) support is available in some configurations of the AT-2972T/2, allowing the switch to deliver power to connected devices such as IP cameras and wireless access points. This capability simplifies installations and reduces the need for additional power sources, streamlining the deployment of network devices.

Furthermore, the switch is designed with energy efficiency in mind, adhering to environmental standards that help organizations reduce their carbon footprint while cutting energy costs.

In summary, the Allied Telesis AT-2972T/2 stands out as a versatile and robust Fast Ethernet switch, equipped with essential features like VLAN support, QoS, PoE, and advanced diagnostics. Its combination of performance, management capabilities, and energy efficiency makes it an excellent choice for businesses aiming to build a reliable and future-proof network infrastructure.