3Com 510M-FBP, 5102M-FBP Interpreting the 10BASE-FB Module LEDs, LED Name Color State Indicates

Page 77

Table 3-5 describes how to interpret the 10BASE-FB Module LEDs.

Table 3-5. Interpreting the 10BASE-FB Module LEDs

LED Name

Color

State

Indicates

 

 

 

 

Activity

yellow

Off

No packets are received on the

 

 

 

fiber segment.

 

 

 

 

(Ports 1-4)

 

On

Constant activity on the fiber

 

 

 

segment.

 

 

 

 

 

 

Blinking

Module receives packets from

 

 

 

segment to which it is attached.

 

 

 

 

Status

green

Off

Port disabled.

(Ports 1-4)

 

 

 

 

On

Port enabled or in standby and link

 

 

 

 

 

integrity is OK.

 

 

 

 

 

 

1 blink

No light detected.

 

 

 

 

 

 

2 blinks

Jabber.

 

 

 

 

 

 

3 blinks

Partition.

 

 

 

 

 

 

4 blinks

Remote fault.

 

 

 

 

 

 

5 blinks

Invalid data received.

 

 

 

 

 

 

6 blinks

Low light received (you can disable

 

 

 

it using Low Light switch setting).

 

 

 

 

Redundancy

green

Off

Redundancy is disabled; ports are

(Ports 1-2)

 

 

independent of each other.

(Ports 3-4)

 

 

 

 

On

Redundancy is enabled between

 

 

 

 

 

ports 1 & 2 and 3 & 4.

 

 

 

 

 

 

Blinking

Switchover has taken place or there

 

 

 

has been a link failure.

 

 

 

 

Installing and Operating the Module 3 - 21

Image 77
Contents Page VDE Class B Compliance Restricted Rights Page Contents Installing and Operating the Module Appendix a Specifications Page Figures Page Tables Page Audience How to Use This GuideStructure of This Guide Usr/snm/agents Document ConventionsConvention Indicates Example 3Com Documents Related DocumentsReference Documents Slot ONline System Concentrator Installation and OperationPage Introduction 10BASE-FB Module Descriptions Introduction 1 Theory of Operation 10BASE-FB ComplianceBASE-FB Module Connections 3Com Product Part Number Compatibility With Other Ethernet Fiber ProductsBASE-FB Module Compatibility Designing and Expanding the Network Understanding the General Rules Rules for Configuring a NetworkBasic Network Rules Rule Definition Recommendations/NotesDefinition Recommendations/Notes Is actually equal to 1.1 meters LAN Product Equivalent Fiber Equivalent Fiber DistancesEquivalent Fiber Distances of LAN Products Determining Maximum Fiber Link Distances Determining Link Budget Calculating Maximum Link DistancePower ONline 10BASE-FB Module Optical Power Budget Normal PowerLink Link Loss DBmBASE-FB Optical Power Budget ONline 10BASE-FB Module Optical Power Budget High PowerCable Size Used Transmit Receive Optical Power Micron ONline toAttenuation Typical Fiber Loss Characteristics Connector and Splice Insertion LossMeter Fiber Link With Mechanical Splice Example 1700 Meter Fiber Link With Mechanical SpliceMeter Fiber Link Through Two Patch Panels Example 2000 Meter Fiber Link Through Two Patch PanelsChoosing a Network Backbone Cabling Structure Star-Wiring Configuration Star ConfigurationSerial Configuration Using 10BASE-FB Modules Serial ConfigurationFiber Backbone, Fiber-to-the-Desk 10BASE-FB Module ConfigurationsAll-Fiber Network Network With 3 Concentrators Example Network With 3 ConcentratorsExample Network with 8 Concentrators Network Configured With 8 ConcentratorsFiber Equivalent Distances Between Transceivers Fiber Backbone, Unshielded Twisted Pair to-the-Desk Example Sample Configuration Distance CalculationSample Configuration Distance Calculation Fiber Backbone, Coaxial Connection Example Connecting a Thin Ethernet 10BASE2 SegmentDesigning and Expanding the Network 2 Standard Redundant Configuration In this configuration Fault-Tolerant ConfigurationsConfiguring Ports for Fault Tolerance Setting Redundancy 10. Redundant Fiber Backbone Configuration Implementing Total Backbone Fault Tolerance 11. Total Backbone Fault-Tolerant Configuration 12. Fiber Network With 3 Concentrators Page Installing and Operating the Module Precautionary Procedures Unpacking Procedures Step Procedure Section Title Quick InstallationQuick Installation Procedures Setting the Dip Switches BASE-FB Module Dip Switch Locations Switch Label Function Factory Switch Setting Default Off Setting Dip Switch S1Dip Switch S1 Settings for Switches 1 Port-Switching Module Port Dip Switch S1 Settings for Switches 3 toModule-Switching Module Channel SelectionSwitch Label Function Factory Switch Setting Default Setting Dip Switch S2Dip Switch S2 Settings Enable/disable Disable Module Low Light Detection Not Used Installing the ModuleInstalling the 10BASE-FB Module BASE-FB Module Connection Configuring the Module Enabling Ports Selecting a Network Enabling Port Redundancy You can enable port redundancy in one of the following waysEnabling Low Light Warning Enabling Optical PowerSaving Module Configuration Showing Module ConfigurationMonitoring the Front Panel Page LED Name Color State Indicates Interpreting the 10BASE-FB Module LEDsNetwork Check Codes LED State Network ConfigurationVerifying LED and Network Assignments Troubleshooting Possible Cause Corrective Action Troubleshooting Using the Port Activity LEDsTroubleshooting Using the Port Activity LEDs LED State Indication Possible Cause Corrective Action Troubleshooting Using the Port Status LEDsTroubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDs Troubleshooting Using the Port Status LEDs 10BASE-FL Technical Assistance Page Specifications Table A-1. General Specifications General SpecificationsTransmitter Specifications Optical SpecificationsTable A-2. Transmit Power Cable Type Normal Power High PowerSupported Fiber Optic Cables Receiver SpecificationsTable A-3. Receiver Specifications Table A-4. Fiber Optic Interface Specifications Power RequirementsTable A-5. Power Requirements Fiber Optic InterfaceMechanical Specifications Environmental SpecificationsTable A-6. Electrical Specifications Table A-7. Mechanical Specifications10BASE-FB Cables 10BASE-FB Cable and Connector SpecificationsTable A-8 BASE-FB Module Part Numbers 10BASE-FB ConnectorsPort-Switching Connector Type On-line Technical Support Technical SupportWorld Wide Web Site Support from Your Network SupplierEmail Technical Support Support from 3Com Returning Products for Repair Accessing the 3Com MIB3Com Technical Publications Page Index Installing Link Budget Redundant Link, 3-16Redundancy LED Unpacking Procedures, 3-3Unshielded Twisted Pair Cable