Adaptec ATA II 1430SA, ATA II 1220SA, ATA II 1420SA manual Index

Page 76

Index

A

ACU

creating arrays 52 Adaptec customer support 3 Adaptec Flash Utility. See AFU

Adaptec RAID Configuration Utility. See HRCONF Adaptec Storage Manager

installing 37 AFU 38

Array Configuration Utility. See ACU arrays

creating (ACU) 52 non-RAID 49 RAID 1 50 RAID 10 50

C

customer support 3

D

data striping 48 disk drives

connecting to SATA controllers 24 failure recovery

multiple arrays 46 multiple disk drives 46 with hot spare 45 without hot spare 46

formatting 59

recovering from failure 45 verifying 59

drivers

installing on Linux 35

installing on NetWare 35 installing on Windows 34

E

electrostatic discharge 67

F

failed disk drives multiple arrays 46 multiple disk drives 46 without hot spare 46

formatting disk drives 59

H

hard disk, hard disk drive, hard drive. See disk drives

I

installation

disk drives (SATA) 24

L

Linux

driver installation 35

N

NetWare

driver installation 35 non-RAID arrays 49

P

performance tuning selecting a RAID level 49

Image 76

Contents Serial ATA II 1430SA, 1420SA, 1220SA HostRAID Controllers Copyright Adaptec Customer Support Limited 3-Year Hardware Warranty Regulatory Compliance Statements Contents Installing the HostRAID Controller Disk Drives Understanding Adaptec Storage Manager Safety Information About This Guide What You Need to Know Before You Begin How to Find More InformationTerminology Used in this Guide About Your HostRAID Controller Array Level Features HostRAID Controller FeaturesUpgrading the HostRAID Controller Firmware About the Adaptec 1430SA Controller About the Adaptec 1420SA Controller About the Adaptec 1220SA Controller Kit Contents System Requirements Kit Contents System RequirementsGetting Started Choosing a RAID Level Selecting Disk DrivesSelecting Cables Disk Drives for Your ControllerInstallation Options Basic Installation StepsInstalling with an Operating System Installing on an Existing Operating SystemInstalling the HostRAID Controller Disk Drives Installing the HostRAID Controller Before You BeginConnecting Disk Drives to Sata HostRAID Controllers Determining the Boot ControllerChecking Your Controller and Devices Next StepsCreating a Bootable Array Creating an Array Setting the Boot ControllerCreating an Array with the ACU Select Express configuration..., then click Next Creating an Array with Adaptec Storage ManagerMaking Your Array Bootable Installing the Driver An Operating System Installing with Windows Creating a Driver DiskInstalling with Red Hat Linux Installing with Suse LinuxInstalling with NetWare Installing the Driver on an Existing Operating System Installing on Windows Installing on Red Hat or Suse Linux Installing on NetWareManaging Your Storage Space About the Hrconf Command Line Utility Installing Adaptec Storage ManagerAbout Adaptec Storage Manager About the AFU About the ARC UtilityWhich Utility Should I Use? Understanding Adaptec Storage Manager Features OverviewPhysical Devices View Changing How Drives are DisplayedLogical Devices View Collapsed and Expanded Views Component Views Solving Problems Recovering from a Disk Drive Failure Troubleshooting ChecklistFailed Disk Drive Protected by a Hot Spare Failed Disk Drive Not Protected by a Hot Spare Failure in Multiple Arrays SimultaneouslyDisk Drive Failure in a RAID 0 Array Multiple Failures in the Same ArrayUnderstanding RAID Selecting a RAID Level and Tuning Performance RAID Technology OverviewUnderstanding Drive Segments Stripe-unit SizeRAID 0 Non-RAID Arrays RAIDRAID 1 Arrays RAID 10 ArraysUsing the ARC Utility Introduction to the ARC Utility Running the ARC UtilityCreating and Managing Arrays Creating a New ArrayRAID Managing Arrays Rebuilding ArraysForce from Offline Configuring Disk Drives Managing Bootable Arrays and DevicesAdding/Deleting Hotspares Using SATASelect Atapi SupportSATASelect Options SmartFormatting and Verifying Disk Drives Using the AFU for DOS System Requirements IntroductionCompatibility Running the AFU from the Command Line Running the AFU from the GUISave Update AFU Command Line Step-by-Step Command SwitchesAfu update /C controllernumber Safety Information Electrostatic Discharge ESDTechnical Specifications DC Power Requirements Environmental SpecificationsCurrent Requirements Glossary See channel Initialize See configure Mirrored array/mirroring See RAID 1, RAID Area on each disk reserved for use by the RAID controller See simple volume, spanned volume Index Scsi Adaptec, Inc