Adder Technology SV4PRO Appendix A. Cable and connector specifications, A2. SmartView to PCs 1 to

Page 38

Appendix A. Cable and connector specifications

IMPORTANT NOTE

The maximum cable lengths supported vary widely between devices and cables. It may be possible to use cables that are longer than those specified below with certain PCs and peripherals but this cannot be guaranteed. If you experience problems try using shorter cables.

A1. Keyboard, monitor and mouse to SmartView

Cable specification:

All of the shared devices plug directly into the relevant ports at the rear of the SmartView. If you use an AT style keyboard you will need an AT (5 pin DIN female) to PS/2 (6 pin mini-DIN male) converter. Keyboard, monitor and mouse extension cables can be used to increase the distance from SmartView up to 10m. Most keyboards and mice will also operate at distances of 20 metres.

A2. SmartView to PCs 1 to 16

Cable specifications:

Video - 15 pin high density male D connector to 15 pin high density male D connector wired as a standard VGA PC to monitor cable. There are two types commonly available. The best type cables which will give excellent quality are constructed with coaxial cable cores. Cheaper ‘data’ cables are often used, but can degrade video quality if used over longer distances. Avoid using 'data' cables longer than 2 metres unless the video quality is not important. Good quality coaxial video cables may be run at distances up to 50 metres with little loss of video quality.

Keyboard and PS/2 mice - 6 pin mini-DIN male connector to 6 pin mini-DIN male connector with all lines connected straight through (1-1,2-2 etc.). If the PC has a 5- pin DIN AT style keyboard connector you will need a PS/2 to AT keyboard adapter 6-pin mini-DIN female to 5-pin DIN male (readily available). Cables should be no longer than 30 metres.

SmartView

Installation and Use

Page 37

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Smart View PRO About this manual Safety informationWarranty Radio Frequency Energy European EMC directive 89/336/EECContents SmartView configuration options AppendicesKey features IntroductionPackage contents Product information SmartView SV8PROSmartView SV4PRO SmartView SV12PRO SmartView SV16PRO Installation What you will needConnecting your devices Mounting the SmartViewTo enter configure mode at power on Configuring your PCsConfiguring the SmartView To enter configure mode whilst the SmartView is runningSummary of SmartView configuration options H2f EfU4 SmartView channels are switchable using 3 button mouse Other useful installation information Re-enabling a disconnected PS/2 mouse SmartView Installation and Use Front panel keys and remote controller Using the SmartViewPower on status Status lightsAuto key Auto and Select keys pressed together Lock functionStatus display Using the dual control ports a and B Keyboard hotkey control‘HOTKEYs’ and ‘1 then 2’ selects channel ‘HOTKEYs’ and ‘1 then 0’ selects channel‘HOTKEYs’ and ‘1 then 1’ selects channel ‘HOTKEYs’ and ‘1 then 3’ selects channelOn Screen Menu control SmartView Installation and Use Selecting a computer on the menu list Deleting a computer from the menu listEditing a computer on the menu list Cascading SmartViews Mouse controlRS232 control Summary of keys used by the menu and their functionSmartView Installation and Use Typical cascade of two SmartViews Screen saver time delay Autoscan ‘lock on’ mode and delay timeSmartView Installation and Use Mouse mode and mouse switching of channels Keyboard hotkey combination Firmware functions version query, mouse restore and reset Display appearance optionsSetting a security password OFREDgExit configure mode Cascade query codeCable specifications Appendix A. Cable and connector specificationsCable specification A1. Keyboard, monitor and mouse to SmartViewA3. Expansion port pin assignments Action Appendix B. Problem SolvingProblem Mouse causes channel to change Problem SmartView Installation and Use S TA L L AT I O N & U S E
Related manuals
Manual 44 pages 28.78 Kb
Top Page Image Contents