Agilent Technologies 8510XF Verification kits, Test port cables and adapters, Device under test

Page 17
Verification kits

Verification kits

Verification kits are used to verify the performance specifications of an 8510 system. All kits include a precision Zo airline, mismatched airline and fixed attenuators. Measured data and uncertainties traceable to the U.S. National Institute of Standards and Technology (NIST) are included with each kit. Compliance with MIL-STD 45662A is available for an extra charge

Choose a verification kit for each connector type required.

Verification

Connector

Frequency

Verification

Connector

Frequency

kit

type

range (GHz)

kit

type

range (GHz)

 

 

 

 

 

 

 

85051B

7 mm

0.045

- 18

R11645A

WR-28

26.5 - 40

85053B

3.5 mm

0.045

- 26.5

Q11645A

WR-22

33

- 50

85055A

Type-N

0.045

- 18

U11645A

WR-19

40

- 60

85057B

2.4 mm

0.045

- 50

V11645A

WR-15

50

- 75

 

 

 

 

W11645A

WR-10

75

- 110

 

 

 

 

 

 

 

 

Test port cables and adapters

Test port cables and adapter sets are available for various connector types. Special test port adapter sets convert the rugged ports of the network analyzer test set to the desired connector interface. Each kit contains two adapters, one male and one female. Both the cables and the test port adapters have one spe- cial female connector which is designed to connect directly to the 3.5 mm test port (2.4 mm for 8517B). This side of the cable or adapter can only be connected to the test set port and cannot be mated to a standard 3.5 mm (or 2.4 mm) male connector. Choose one of the configurations shown.

Configuration A. This cable arrangement is for applications where the device under test is connected directly to the test set port. This setup offers the best mechanical rigidity for device connection. To adapt the test set port (port 1) to the device under test, choose the appropriate special adapter set. In addition to converting the test port to the desired interface, these adapters also func- tion as “test port savers” which protect the test set from damage and wear due to heavy use.

For Agilent 8514B/8515A/85110A test sets (3.5 mm rugged test port connectors)

 

Cables/adapter

Connector type

 

 

(on device side of cable/adapter)

 

 

 

For 3.5 mm devices

85131C semi-rigid cable or

3.5 mm (f)

 

85131E flexible cable

3.5 mm (f )

 

85130D adapter set

3.5 mm (m and f)

 

 

 

For 7 mm devices

85132C semi-rigid cable or

7 mm

 

85132E flexible cable

7 mm

 

85130B adapter set

7 mm

 

 

For Type-N devices

Use 7 mm cables and the 7 mm-to-Type-N

 

adapters included in the 85054B/D

 

 

Type-N calibration kit

 

 

 

 

For Agilent 8517B test sets (2.4-mm rugged test port connectors)

 

Cables/adapter

Connector type

 

 

(on device side of cable/adapter)

For 2.4 mm devices

85133C semi-rigid cable or

2.4 mm (f)

 

85133E flexible cable

2.4 mm (f )

 

85130G adapter set

2.4 mm (m and f)

For 3.5 mm devices

85134C semi-rigid cable or

3.5 mm (f)

 

85134E flexible cable

3.5 mm (f )

 

85130F adapter set

3.5 mm (m and f)

For 7 mm devices

85135C semi-rigid cable or

7 mm

 

85135E flexible cable

7 mm

 

85130E adapter set

7 mm

Device

under

test

Configuration A

Network analyzer

test set

Test port cables and adapters Test port adapter

Single cable

17

Image 17
Contents on-wafer configuration Agilent Upgrade Guide for the Vector Network AnalyzerProduct Note 85107B, 45 MHz to 50 GHz in coaxTable of Contents Vector network analyzer VNA overview Signal separationSource Receiver/Detector Processor/DisplaySignal 8510 VNA = system8510Receiver/detector network analyzerAgilent 8510 network analyzer Agilent 8510 family of productsFigure 4. 8510 family of system solutions Table 1. Hardware revision and measurement capabilityFigure 5. 8510 firmware upgrade kits Agilent 8510 Firmware upgrade kitsTable 2. Firmware revision and measurement capability 8510CTable 3. Family of test sets Test SetsTable 5. 8360 general purpose synthesizers SourcesTable 4. 8510-dedicated sources Upgrading individual components Upgrade considerationsUpgrading the 85103E8530A 8510C8530A microwave receiver and 8510C Figure 7. 8510 to 8530 upgrade pathsExpanding measurement capabilities Test set upgradesAdding pulse capabilities Option Adding time domain capabilitiesFigure 8. 8510 family of system solutions + ORUpgrading systems 4. What measurement accessories do I need? System upgrades2. What test set do I need? 3. What source do I need?Upgrades for 85107B, 85109C Measurement accessories Examples of upgrade pathsUpgrade to 85106D waveguide system to operate in V-band 85107B 45 MHz to 50 GHz current systemCalibration kits Test port cables and adapters Verification kitsConfiguration A Network analyzer test set Device under testFor 8514B/8515A/85110A test sets 3.5 mm rugged test port connectors Configuration B Network analyzer test set Cable set Device under testFor 85110L Test sets 7 mm rugged test port connectors For 8517B Test sets 2.4 mm rugged test port connectorsPub. number Related literatureProduct overviews Product notesFor more information on the 8510 VNA visit Agilent Technologies’ Test and Measurement Support, Servicesand Assistance Our Promise