Casio DT-X5 manual DIP Switch Setting for HA-A61IO

Page 30

2.5 DIP Switch Setting for HA-A61IO

The DIP switch is located on the rear side of the Bridge Satellite Cradle. Change the ON/OFF settings according to your required system configuration. The new settings do not go into effect until the power switch is turned off and then back on again.

ON（Upper side）

OFF（Lower side）

Not used (Always set to "OFF")

Not used (Always set to "OFF")

Host computer interface
	Interface	6
	RS-232C	OFF
	USB *	ON
Termination setting for daisy chain connection
	Termination	5
	At middle	OFF
	No chain/Termination*	ON
Connection mode
	Mode	3	4
	With Host PC*	OFF	OFF
	Chain connection	ON	OFF
Communication speed between Cradles
	Baud rate	1	2
	115,200bps *	ON	OFF

* : Default setting.

Fig. 2.3

Note:

Other DIP switch settings are used for testing and inspection purposes. Because of this, you should never use any DIP settings other than those described above.

30

Image 30

Contents DT-X5 Series Hardware Manual Table of Contents Precautions Handling Precautions Safety Battery Pack General Editorial Record Preface Enhanced communicating functions Overview FeaturesIncorporates .NET technology Superb reading capabilityAvailable Models and Options Page Options And Interfaces DT-X5General Guide Views for DT-X5M10E, DT-X5M10RFront view in .3 is for all the models of DT-X5 series Satellite Cradle Power contacts Names of parts Description IndicatorWhen a reading error has occurred Cradle-type Battery ChargerHA-A34AT Battery Charger Car Mount Unit ViewHA-A61IO and HA-A60IO Cradles ViewsTop Right Back Front Requires installation of a special driver on the PC Desktop unit in the case of a wall mount configurationDIP switches Installation of a special driver on the PCCharge status 3 DT-5022CHG Dual Battery ChargerIndicators Bottom Connection attachmentsHA-A20BAT and DT-5025LBAT Battery Packs Bottom Left Top Side Charge/Power supply terminalsLeftTop Side Hardware Specifications DT-X5 Specification RemarkContinue Battery Power with HA-A20BAT DT-5025LBAT is fully Lithium-ion battery packMemory backup Is room temperatureLithium-ion battery Is at room temperatureDigit/5-digit addon Yes Operating hours by modelLaser NS output YesEAN8/13 Composite Code49 YesYes Codablock F RSS CompositeOr more Test chart Dedicated test patternReference for Laser Scanner Performance 60 mm At contact 355 mm At 400 mm depthUnit mm Reference for C-MOS Imager Performance PCSOr greater Test chartResolution 1D 0.25 mm / 2D 0.5 mm Read judgment Times per 10 scans First Decode DepthHA-A60IO, HA-A61IO USBWeight Desktop state Approx g Weight/DimensionsDimensions Desktop state Approx W x 125 D x 128 H mm Approx W x 148 D x 153 H mmHA-A34AT OFFDimensions Configuration Wall-mount HA-A30CHGDIP Switch Setting for HA-A61IO Power Status Indications with LEDsBasic Block Power Supply BlockDT-5022CHG Interface BlockBattery Charge Block HA-A20BAT, DT-5025LBAT Product Identification and Reference Numbers Box Temperature 20 ºC to 60 ºC Humidity 90 %RH or less Quality ReferencesEnvironmental Performances DT-X5 Box Temperature 10 ºC to 50 ºC Humidity 30% to 90%RH HA-A60IO, HA-A61IO, HA-A30CHGSplash proof Not applicable 4 DT-5022CHG Storage 10 to 55 ºC With carton box Humidity OperationElectrical Performances DT-X5 4 DT-5022CHG Cm or less 3 DT-5022CHGCorners Master carton box Cm or lessCm or less Faces, 3 edges, 1 corner onto P-tile Protection from short Reliability DT-X5210,000 hours or more Charge terminalsEMC, EMI, Safety, Wlan /Bluetooth type approvals Compliance DT-X5AD-S42120AE, AD-S45150AU, AD-S45150AE Cable Specifications For Chain Connection and Short Length For Chain Connection and Long Length View from sidePrecautions Handling Precautions Precautions for short-term storage 1 to 2 daysPrecautions for long-term storage over one week Safety Battery Pack General Memory protection