Casio SE-S10 user manual Mode Switch, Display, Operator display

Page 6

Getting to know your cash register

Getting to know your cash register

Mode Switch

REG CAL X Z

OFF

RF

PGM

The position of the Mode Switch controls the type of operations you can perform on the cash register. The PROGRAM key (marked PGM) can be select any Mode Switch setting, while OPERATOR key (marked OP) can be used to select OFF, REG or CAL only.

OP key

PGM RF OFF REG CAL

X Z

●

●

●

 

PGM key

● ● ●

●

●

● ●

OP PGM

OP key PGM key

Note:

An error is gener- ated (E01 displayed) whenever the position of the Mode Switch is changed during regis- tration.

OFF

In this position, the power of the cash register is off.

REG (Register)

This is the position used for registration of normal transactions.

RF (Refund)

This is the position used for registration of refunds.

CAL (Calculator)

This is the position used for calculator mode.

PGM (Programming)

This is the position used to program the cash register to suit the needs of your store.

X (Read)

This is the position used to produce reports of daily sales totals with- out clearing the totals.

Z (Reset)

This is the position used to produce reports of daily sales totals. This setting clears the totals.

Display

Operator display

Customer display











!

!Department Number Display

Anytime you press a department key to register a unit price, the corresponding department number appears here.

@PLU Number Display

Anytime you perform a PLU registration, the cor- responding PLU number appears here.

#Number of Repeat Display

Anytime you perform “repeat registration” (page 14), the number of repeats appears here.

Note that only one digit is displayed for the num- ber of repeats.

E

$Numeric Display

Entered values (unit prices or quantities) and calculated values (subtotals, totals or change amount due) are displayed here. The capacity of the display is 8 digits.

This part of the display can be used to show the current time or date between registrations (page 40).

%Character Display

In the character programming (P2) mode, it shows the last entered character.

The total (T) or change (C) appears when a subtotal, total, or change is obtained.

In the paper saving mode, it shows *.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents SE-S10 Original Carton/Package Power SupplyCleaning LocationSafety precautions About the iconsIcon examples Introduction Contents Mode Switch DisplayOperator display Register Mode Calculator ModeKeyboard After Closing The Store Before Opening The StoreWhile The Store Is Open OtherLoading Memory Protection Battery Loading Paper RollTo load receipt paper Setting the Cash Register If you want to use a printer as journal printerTo remove receipt paper To remove journal paperBasic Programming for Quick Start Mode SwitchProcedure PurposeXvxx Multiple registra- tion of the same items Basic Operation after Basic ProgrammingBasic operation ZCBBefore you press a depart- ment key Split cash Charge salesCorrections Ykey clears the last item enteredBB? Department keyAfter you pressed a XX?REG Financial Report Read/Reset ReportDaily Management Report ElectronicMode Switch to Reset Reset ReportMode Switch to Read ReportRate for percent key Various ProgrammingUnit price for Departments For Departments?VZ Status for DepartmentStatus for percent key ?BZStatus for Percent keyControls General featuresTo set general ?NXXTo set printing controls ?BXXReceipt printing character Key catch tone Printer switch forReceipt or Journal To set report printing controlsUnit Prices for PLUs PLU settingLinkage with Departments IV p??????p Setting the Tax Rate Rounding?ZXB ?CXB?CXN List fror Issue category listTo program department PLU, clerk name, receipt message Programming department nameProgramming department PLU Reset department nameReset PLU name XizV?Xp ?izV?CpKeyboard PGM 2 mode, the keyboard becomes character setting keyboardCharacter Vvvzzzccc pProgramming receipt message Programming PLU nameProgramming clerk name XVVNNBB++Alphabetical order → s → ß Printing to read All Preset Data Printing preset PLU settings PLU No./ProgramVarious Operations Registration usingPreset price For Departments Single-Item Sales??G RefundXB?? ??SPLU registration Read ResetPLU operation PLU Single-Item SaleAdjusting the Date Other registrationsMode SwitchAdjusting the Time Reading the Time and DateBNMj Reduction on subtotalZxcv ??? PDCashier AssignmentPremium/ Discount Examples On REG mode On CAL modeOn REG mode Memory recallSetting for calculator operation Troubleshooting Case of power failureIf the following things happen When the L sign appears on the display About the low battery indicatorSpecifications When the cash drawer does not open
Top Page Image Contents