Casio SE-S10 user manual Daily Management Report, Financial Report, Read/Reset Report, Electronic

Page 18

Part-1 QUICK START OPERATION

10. Daily Management Report

This section tells you the procedures to use to produce reports of the transaction data stored in the cash register's memory.

Important

Remember that when you issue a reset (Z) report, the data that is reported is cleared from the applicable totalizers. To view data without clearing totalizers, issue a read (X) report.

10-1 Financial Report	Operation	Printout
10-1 Financial Report

Mode Switch

CAL X

REG Z

OFF

RF

PGM

h

08-01-2010

X

FLASH

GROSS TOTAL

NET TOTAL

CASH-INDW

CHARGE-INDW

CHECK-INDW

19:10

0070

X— Read Symbol

QT	57— Gross Sales No. of items
•270.48— Gross Sales Amount
No	38— Net Sales No. of Customers
•271.24— Net Sales Amount
•197.57— Cash Total in Drawer
	•18.19— Charge Total in Drawer
	•45.18— Check Total in Drawer

10-2 Read/Reset

Report

10-2-1 Electronic	Operation	Printout
journal Report
journal Report		10-01-2010		19:25
		X		0173
Mode Switch to X	B<p	0058 EJ	X	— Read Symbol
		0058 EJ	X	— Read Symbol
	(Date)*	REG		17:34— Journal
	p			0023
	(Consecutive No.)*	DEPT01		•2.24
		CA	•2.24

p

*If you want to designate read range, enter date and/ or cosecutive No..

If you want to reset the electronic journal, just press B<pin Z mode.

• Journal is saved in the memory and you can take a report any time you want.

E

18

Image 18

Contents SE-S10 Original Carton/Package Power SupplyCleaning LocationSafety precautions About the iconsIcon examples Introduction Contents Mode Switch DisplayOperator display Register Mode Calculator ModeKeyboard After Closing The Store Before Opening The StoreWhile The Store Is Open OtherLoading Memory Protection Battery Loading Paper RollTo load receipt paper Setting the Cash Register If you want to use a printer as journal printerTo remove receipt paper To remove journal paperBasic Programming for Quick Start Mode SwitchProcedure PurposeXvxx Multiple registra- tion of the same items Basic Operation after Basic ProgrammingBasic operation ZCBBefore you press a depart- ment key Split cash Charge salesCorrections Ykey clears the last item enteredBB? Department keyAfter you pressed a XX?REG Financial Report Read/Reset ReportDaily Management Report ElectronicMode Switch to Reset Reset ReportMode Switch to Read ReportRate for percent key Various ProgrammingUnit price for Departments For Departments?VZ Status for DepartmentStatus for percent key ?BZStatus for Percent keyControls General featuresTo set general ?NXXTo set printing controls ?BXXReceipt printing character Key catch tone Printer switch forReceipt or Journal To set report printing controlsUnit Prices for PLUs PLU settingLinkage with Departments IV p??????p Setting the Tax Rate Rounding?ZXB ?CXB?CXN List fror Issue category listTo program department PLU, clerk name, receipt message Programming department nameProgramming department PLU Reset department nameReset PLU name XizV?Xp ?izV?CpKeyboard PGM 2 mode, the keyboard becomes character setting keyboardCharacter Vvvzzzccc pProgramming receipt message Programming PLU nameProgramming clerk name XVVNNBB++Alphabetical order → s → ß Printing to read All Preset Data Printing preset PLU settings PLU No./ProgramVarious Operations Registration usingPreset price For Departments Single-Item Sales??G RefundXB?? ??SPLU registration Read ResetPLU operation PLU Single-Item SaleAdjusting the Date Other registrationsMode SwitchAdjusting the Time Reading the Time and DateBNMj Reduction on subtotalZxcv ??? PDCashier AssignmentPremium/ Discount Examples On REG mode On CAL modeOn REG mode Memory recallSetting for calculator operation Troubleshooting Case of power failureIf the following things happen When the L sign appears on the display About the low battery indicatorSpeciﬁcations When the cash drawer does not open