Samsung SP-A900B LED Indications, Clearing Indicator Problems, ClassificationState, Measures

Page 10

Power Cable

Remote Control/ 2 Batteries

Cleaning Cloth

 

(Not available in all locations)

LED Indications

 

:Light is On

:Light is Blinking

:Light is Off

STAND BY

LAMP TEMP

Information

If you press the POWER button on the remote control or projector, the screen appears within 30 seconds.

The projector is in normal operating condition.

This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed.

The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off the inside of the projector. (Lasts for about 1 minute and 30 seconds)

Refer to Action 1 below if the cooling fan inside the projector is not in normal operation condition.

Refer to Action 2 below if the lamp cover protecting the lamp unit is not closed properly.

Power is turned off automatically when temperature inside of the projector goes beyond the control limit. Refer to Action 3.

A problem has occurred when operating the DDP IC in the product. Refer to Action 4.

A problem has occurred with the operation of the lamp. Refer to Action 5.

The lifetime of the lamp has expired. Refer to Action 6.

The memory in the product is not operating normally. Contact a service center.

The power for the product is not operating normally. Contact a service center.

A problem has occurred when operating the color wheel in the product. Refer to Action 4.

Clearing Indicator Problems

ClassificationState

When the cooling fan

Action 1 system is not in normal operating condition.

Measures

If the symptom remains even after disconnecting and then reconnecting the power cord and turning the projector on again, contact your product provider or our service center.

Action 2

When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition.

Check whether the screws at the bottom side of the projector are fastened correctly. If they are abnormally fastened, contact your product distributor or service center.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Product color and shape may vary depending On the model Under no circumstances touch the power plug with wet hands Insert the power plug firmly so that it does not come looseDo not use loose power outlets or damaged power cables Do not plug multiple devices into a single wall outletUnplug the power plug before cleaning the product Keep the power cord away from heatersDo not drop the product while carrying it Place the product on the ground carefullyKeep the product out of children’s reach Do not disassemble, or attempt to fix or modify the product If swallowed, see a doctor immediatelyMake sure to place your remote control on a table or desk Take care not to lose the lens cover of the productPage Optical engine with advanced DLP technology Front/Upper SidePackage Contents Lens Lens Position Moving DialClassificationState Clearing Indicator ProblemsLED Indications MeasuresCenter Rear SideCOMP1 Move /ENTERModel Supported Display Modes Supported Resolution/Size Modes Picture Position Modes DVI Select Menu Setup Install Front-Floor Installing the ProjectorSelect Menu Setup Install Rear-Floor Zoom and Focus AdjustmentAdjusting the Lens Position Moving Dial Leveling with Adjustable FeetScreen Size and Projection Distance Screen VerticalYmm MinZmm MaxZmm Offset YmmPage Connecting a DVD player/Cable/Satellite Box to HDMI/DVI Rear of ProjectorUsing the Projector Connecting a DVD player/Cable/Satellite Box via ComponentConnecting to VCR/Camcorder Connecting to PC Using the Projector Component Screen DescriptionPlay/Stop AdjustmentVideo Description Play/StopFor Hdmi Mode Color Temperature Offset GainPosition Adjust the screen position if it is not aligned Zoom1Off SignalsOff Shows the picture in the original color ScreenLight Setting Adjustment DescriptionInstall Maximum and then perform Fine Adjustment againTime Sec 90 sec 10 sec 120 sec 30 sec Translucency Opaque Low Medium High60 sec Off Symptoms Troubleshooting SymptomsTroubleshooting Screen and External SourcePage To clean the interior of the projector To clean the exterior and lens of the projectorClean the projector using a soft dry cloth Lamp ReplacementLamp Replacement Procedure North AmericaLatin America EuropeSlovakia Analog Broadcast Backlight Remote ControlColor Temperature Antenna in PortExternal Input Gamma ModeRS-232C Port Service Input Port Overscan
Top Page Image Contents