Samsung SP-A900B manual Center, Rear Side

Page 11

When temperature inside

Action 3 of the projector becomes too high.

Adjust the installation state of your projector by referring to the Installation Precautions section listed above. Cool down your projector sufficiently and then operate it again. If the same problem occurs continually, contact your product distributor or service center.

		When the DDP IC or color wheel	Disconnect and reconnect the power cord and start the projector
	Action 4	When the DDP IC or color wheel	again. If the same symptom still occurs, contact your product
		fails to operate.	distributor or service center.
			distributor or service center.
		The lamp
		malfunctions after power	Turn the power off, wait for a sufficient amount of cooling time and
		turns off
	Action 5	turns off	then turn the power on to operate. If the same problem occurs
	Action 5	abnormally or after
		abnormally or after	continually, contact your product distributor or service center.
		powering on right after
		powering on right after
		turning off the projector.
		When the screen becomes	Check the lamp usage time on the Information Display screen. If you
	Action 6	When the screen becomes	need to replace the lamp, contact your product distributor or service
	Action 6	darker
		darker	center.
			center.

This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan may cause noise, which does not affect the product performance and is part of normal operation.

Rear Side

1. PC IN Input port	5. RS-232C port
	(For service input terminals)
2. COMPONENT IN 1/2 Input ports
	6. VIDEO IN Input port
3. S-VIDEO IN Input port
	7. Remote Control Signal Receiver
4. POWER Input port
	8. HDMI IN 2, HDMI 1/DVI IN Input port

Image 11

Contents Product color and shape may vary depending On the model Do not plug multiple devices into a single wall outlet Insert the power plug firmly so that it does not come looseDo not use loose power outlets or damaged power cables Under no circumstances touch the power plug with wet handsKeep the power cord away from heaters Unplug the power plug before cleaning the productKeep the product out of children’s reach Place the product on the ground carefullyDo not drop the product while carrying it If swallowed, see a doctor immediately Do not disassemble, or attempt to fix or modify the productTake care not to lose the lens cover of the product Make sure to place your remote control on a table or deskPage Front/Upper Side Optical engine with advanced DLP technologyLens Lens Position Moving Dial Package ContentsMeasures Clearing Indicator ProblemsLED Indications ClassificationStateRear Side CenterMove /ENTER COMP1Model Supported Display Modes Supported Resolution/Size Modes Picture Position Modes DVI Zoom and Focus Adjustment Installing the ProjectorSelect Menu Setup Install Rear-Floor Select Menu Setup Install Front-FloorScreen Size and Projection Distance Leveling with Adjustable FeetAdjusting the Lens Position Moving Dial VerticalYmm MinZmm MaxZmm Offset Ymm ScreenPage Rear of Projector Connecting a DVD player/Cable/Satellite Box to HDMI/DVIConnecting a DVD player/Cable/Satellite Box via Component Using the ProjectorConnecting to VCR/Camcorder Connecting to PC Using the Projector Video Screen DescriptionPlay/Stop AdjustmentComponent Play/Stop DescriptionZoom1 Color Temperature Offset GainPosition Adjust the screen position if it is not aligned For Hdmi ModeScreen SignalsOff Shows the picture in the original color OffMaximum and then perform Fine Adjustment again Adjustment DescriptionInstall Light Setting60 sec Translucency Opaque Low Medium HighTime Sec 90 sec 10 sec 120 sec 30 sec Off Screen and External Source SymptomsTroubleshooting Symptoms TroubleshootingPage Lamp Replacement To clean the exterior and lens of the projectorClean the projector using a soft dry cloth To clean the interior of the projectorNorth America Lamp Replacement ProcedureEurope Latin AmericaSlovakia Antenna in Port Backlight Remote ControlColor Temperature Analog BroadcastOverscan Gamma ModeRS-232C Port Service Input Port External Input