BenQ MX701 user manual Main menu Sub-menu, Options, System, Setup, Advanced

Page 41

SYSTEM

	Main menu Sub-menu			Options
		High Altitude Mode		On/Off
			Mute	On/Off
		Audio Settings	Volume
		Audio Settings	Power On/Off	On/Off
			Power On/Off
			Ring Tone
			Ring Tone
			Lamp Mode	Normal/Economic
		Lamp Settings	Reset Lamp Timer
			Equivalent Lamp Hour
		Security	Change Password
		Security	Change Security	Power On Lock
		Settings	Change Security	Power On Lock
		Settings	Settings	Splash Screen Lock
			Settings	Splash Screen Lock
		Baud Rate		2400/4800/9600/14400/19200/
		Baud Rate		38400/57600/115200
				38400/57600/115200
	5.	Test Pattern		On/Off
	5.		Closed Caption	On/Off
	SYSTEM	Closed Caption	Enable	On/Off
	SYSTEM	Closed Caption	Enable
	SETUP:		Caption Version	CC1/CC2/CC3/CC4
	Advanced	Standby	Network	On/Off
		Standby	Monitor Out	On/Off
		Settings	Audio Pass	Off/Computer 1/Computer 2/
			Through	Video,S-Video/HDMI
				Status
				DHCP
				IP Address
		Network	Wired LAN	Subnet Mask
		Network		Default Gateway
		Settings		DNS Server
				Apply
			AMX Device	On/Off
			Discovery	On/Off
			Discovery
			Mac Address

Reset All Settings

		•	Source
		•	Picture Mode
6.	Current System Status	•	Resolution
INFORMATION	Current System Status	•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 41

Image 41

Contents Welcome Warranty and Copyright Important safetyMaintenance TroubleshootingSafety Instructions Important safety instructionsSafety Instructions Continued following environments Ceiling mounting the projector Introduction Projector featuresOptional accessories Shipping contentsStandard accessories Rear/lower side Projector exterior viewFront/upper side Controls and functions Projectortimings for the displayed image DownRemote control Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsPositioning your projector Connection Connecting audio Connecting video source devicesStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjustingthe image Fine-tuningthe image size and clarityCorrecting keystone Current input signal Using the menusSYSTEM SETUP Basic SYSTEM SETUP BasicUtilizing the password function Using a security cable lockSetting a password Securing the projectorEntering the password recall procedure If you forget the passwordDisabling the password function Changing the passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorOptimizing the image Adjusting Brightness Fine-tuningthe image quality in user modesAdjusting Contrast Adjusting Color3D Color Management To cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsHiding the image Locking control keysTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Cable connection Adjusting the soundIf you are in a non-DHCPenvironment ii.You can adjust the Network Settings Operation Shutting down the projector Direct power offMenu system Menu operationOptions 4. SYSTEM SETUP BasicMain menu Sub-menu Main menu Sub-menu SETUPOptions SYSTEMDescription of each menu 1. DISPLAY menu 2. PICTURE menu 3. SOURCE menu 4. SYSTEM SETUP Basic menu Function 5. SYSTEM SETUP Advanced menu Settings 5. SYSTEM SETUP Advanced menuSettings Reset AllFunction 6. INFORMATION menuDescription CurrentCleaning the lens MaintenanceCleaning the projector case Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Message Timing of replacing the lampStatus 4.Disconnect the lamp connector from the Replacing the lamp52 Maintenance 2.Loosen the screw that secures the lamp7.Use the handle to slowly pull the lamp out of Resetting the lamp timer Power events IndicatorsLight Status & DescriptionTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsCeiling Mount screw M4 x 8 Max L = 8 mmUXGA Timing chartSupported timing for PC input 60 Specifications Supported timing for HDMI HDCP inputSupported timing for Video and S-Videoinputs Supported timing for Component-YPbPr inputTiming TimingLimited warranty Warranty and Copyright informationCopyright Disclaimer