BenQ MX701 user manual DISPLAY menu 2. PICTURE menu

Page 43
1. DISPLAY menu

1. DISPLAY menu

2. PICTURE menu

Function

Description

Teaching

Provides several preset patterns for various teaching purposes.

Choose Blackboard or Whiteboard first by pressing / and press

Template

/ to choose the pattern you need. Press MODE/ENTER to activate

 

the pattern.

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 28 for details.

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 28 for

 

details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on page

29 for details.

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 29 for details.

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a video

Color

image. See "Adjusting Color" on page 29 for details.

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

Adjusts the red and green color tones of the image. See "Adjusting Tint"

Tint

on page 29 for details.

This function is only available when a Video or S-Video signal is

 

 

selected and the system format is NTSC.

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 29 for details.

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

Brilliant Color

See "Adjusting Brilliant Color" on page 29 for details.

 

 

Color

See "Selecting a color temperature" on page 29 for details.

Temperature

 

 

 

3D Color

See "3D Color Management" on page 30 for details.

Management

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

Operation 43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Welcome Troubleshooting Important safetyWarranty and Copyright MaintenanceSafety Instructions Important safety instructionsSafety Instructions Continued following environments Ceiling mounting the projector Introduction Projector featuresStandard accessories Shipping contentsOptional accessories Front/upper side Projector exterior viewRear/lower side Down ProjectorControls and functions timings for the displayed imageRemote control Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsPositioning your projector Connection Connecting audio Connecting video source devicesStarting up the projector OperationFine-tuningthe image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjustingthe imageCorrecting keystone SYSTEM SETUP Basic Using the menusCurrent input signal SYSTEM SETUP BasicSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordDisabling the password function Changing the passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Using Wall ColorSelecting a picture mode Adjusting Color Fine-tuningthe image quality in user modesAdjusting Brightness Adjusting Contrast3D Color Management To cancel the timer, perform the following steps Setting the presentation timerLocking control keys Remote paging operationsFreezing the image Hiding the imageCreating your own startup screen Operating in a high altitude environmentTo activate the High Altitude Mode Cable connection Adjusting the soundIf you are in a non-DHCPenvironment ii.You can adjust the Network Settings Operation Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu 4. SYSTEM SETUP BasicOptions SYSTEM SETUPMain menu Sub-menu OptionsDescription of each menu 1. DISPLAY menu 2. PICTURE menu 3. SOURCE menu 4. SYSTEM SETUP Basic menu Function 5. SYSTEM SETUP Advanced menu Reset All 5. SYSTEM SETUP Advanced menuSettings SettingsCurrent 6. INFORMATION menuFunction DescriptionCare of the projector MaintenanceCleaning the lens Cleaning the projector caseGetting to know the lamp hour Lamp informationExtending lamp life Status Timing of replacing the lampMessage 2.Loosen the screw that secures the lamp Replacing the lamp4.Disconnect the lamp connector from the 52 Maintenance7.Use the handle to slowly pull the lamp out of Resetting the lamp timer Status & Description IndicatorsPower events LightTroubleshooting Projector specifications SpecificationsM4 x 8 Max L = 8 mm DimensionsCeiling mount installation Ceiling Mount screwSupported timing for PC input Timing chartUXGA 60 Specifications Supported timing for HDMI HDCP inputTiming Supported timing for Component-YPbPr inputSupported timing for Video and S-Videoinputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents