BenQ MX701 Indicators, Light, Status & Description, Power events, Lamp events, Thermal events

Page 55
Indicators

Indicators

Light

Status & Description

 

 

 

 

Power events

 

 

 

 

Off

Off

Orange

Stand-by mode.

Off

Off

Green

Powering up.

Flashing

Off

Off

Green

Normal operation.

 

 

 

• The projector needs 90 seconds to cool down as it was

 

 

 

 

abnormally shut down without the normal cooling down

 

 

 

 

process.

Off

Off

Orange

• The projector needs to cool for 90 seconds after the power

Flashing

 

is turned off.

 

 

 

 

 

 

• The projector has shut down automatically. If you try to re-

 

 

 

 

start the projector, it will shut down again. Please contact

 

 

 

 

your dealer for assistance.

 

 

 

 

 

 

 

 

 

Lamp events

Red

Off

Orange

The projector has shut down automatically. If you try to re-

Flashing

start the projector, it will shut down again. Please contact your

 

 

 

dealer for assistance.

Red

Off

Off

1.

The projector needs 90 seconds to cool down. Or

2.

Please contact your dealer for assistance.

 

 

 

 

 

 

 

 

Thermal events

Off

Red

Off

Red

Red

Off

Green

Red

Off

Orange

Red

Off

Red

Red

Orange

Green

Red

Orange

Red

Red

Red

Green

Red

Red

Red

Red

Green

Green

Red

Green

Red

Green

Off

Orange

Green

Off

Red

Orange

Off

The projector has shut down automatically. If you try to re- start the projector, it will shut down again. Please contact your dealer for assistance.

Maintenance 55

Image 55
Contents Welcome Troubleshooting Important safetyWarranty and Copyright MaintenanceSafety Instructions Important safety instructionsSafety Instructions Continued following environments Ceiling mounting the projector Introduction Projector featuresStandard accessories Shipping contentsOptional accessories Front/upper side Projector exterior viewRear/lower side Down ProjectorControls and functions timings for the displayed imageRemote control Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsPositioning your projector Connection Connecting audio Connecting video source devicesStarting up the projector OperationFine-tuningthe image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjustingthe imageCorrecting keystone SYSTEM SETUP Basic Using the menusCurrent input signal SYSTEM SETUP BasicSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordDisabling the password function Changing the passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Using Wall ColorSelecting a picture mode Adjusting Color Fine-tuningthe image quality in user modesAdjusting Brightness Adjusting Contrast3D Color Management To cancel the timer, perform the following steps Setting the presentation timerLocking control keys Remote paging operationsFreezing the image Hiding the imageCreating your own startup screen Operating in a high altitude environmentTo activate the High Altitude Mode Cable connection Adjusting the soundIf you are in a non-DHCPenvironment ii.You can adjust the Network Settings Operation Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu 4. SYSTEM SETUP BasicOptions SYSTEM SETUPMain menu Sub-menu OptionsDescription of each menu 1. DISPLAY menu 2. PICTURE menu 3. SOURCE menu 4. SYSTEM SETUP Basic menu Function 5. SYSTEM SETUP Advanced menu Reset All 5. SYSTEM SETUP Advanced menuSettings SettingsCurrent 6. INFORMATION menuFunction DescriptionCare of the projector MaintenanceCleaning the lens Cleaning the projector caseGetting to know the lamp hour Lamp informationExtending lamp life Status Timing of replacing the lampMessage 2.Loosen the screw that secures the lamp Replacing the lamp4.Disconnect the lamp connector from the 52 Maintenance7.Use the handle to slowly pull the lamp out of Resetting the lamp timer Status & Description IndicatorsPower events LightTroubleshooting Projector specifications SpecificationsM4 x 8 Max L = 8 mm DimensionsCeiling mount installation Ceiling Mount screwSupported timing for PC input Timing chartUXGA 60 Specifications Supported timing for HDMI HDCP inputTiming Supported timing for Component-YPbPr inputSupported timing for Video and S-Videoinputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright