BenQ MX701 user manual Timing of replacing the lamp, Status, Message

Page 51
Timing of replacing the lamp

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 55 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic selected

 

(See "Getting to know the lamp hour" on page 50),

Order Replacement Lamp

you may continue to operate the projector until

Lamp>XXXX Hours

the next hour lamp warning appears.

 

Press MODE/ENTER to dismiss the message.

Order a new lamp at lamp.benq.com

 

 

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Replace Lamp Soon

normal lamp behavior. You can replace the lamp

 

whenever you notice that the brightness level has

Lamp>XXXX Hours

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

Notice

 

Replace Lamp Now

 

Lamp>XXXX Hours

 

Lamp usage time exceeded

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press MODE/ENTER to dismiss the message.

 

 

Replace lamp (refer to User Manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

Message "XXXX" shown in the above messages are numbers that vary depending on different models.

Maintenance 51

Image 51
Contents Welcome Troubleshooting Important safetyWarranty and Copyright MaintenanceSafety Instructions Important safety instructionsSafety Instructions Continued following environments Ceiling mounting the projector Introduction Projector featuresShipping contents Standard accessoriesOptional accessories Projector exterior view Front/upper sideRear/lower side Down ProjectorControls and functions timings for the displayed imageRemote control Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsPositioning your projector Connection Connecting audio Connecting video source devicesStarting up the projector OperationFine-tuningthe image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjustingthe imageCorrecting keystone SYSTEM SETUP Basic Using the menusCurrent input signal SYSTEM SETUP BasicSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordDisabling the password function Changing the passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Using Wall Color Optimizing the imageSelecting a picture mode Adjusting Color Fine-tuningthe image quality in user modesAdjusting Brightness Adjusting Contrast3D Color Management To cancel the timer, perform the following steps Setting the presentation timerLocking control keys Remote paging operationsFreezing the image Hiding the imageOperating in a high altitude environment Creating your own startup screenTo activate the High Altitude Mode Cable connection Adjusting the soundIf you are in a non-DHCPenvironment ii.You can adjust the Network Settings Operation Shutting down the projector Direct power offMenu system Menu operation4. SYSTEM SETUP Basic Main menu Sub-menuOptions SYSTEM SETUPMain menu Sub-menu OptionsDescription of each menu 1. DISPLAY menu 2. PICTURE menu 3. SOURCE menu 4. SYSTEM SETUP Basic menu Function 5. SYSTEM SETUP Advanced menu Reset All 5. SYSTEM SETUP Advanced menuSettings SettingsCurrent 6. INFORMATION menuFunction DescriptionCare of the projector MaintenanceCleaning the lens Cleaning the projector caseLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp StatusMessage 2.Loosen the screw that secures the lamp Replacing the lamp4.Disconnect the lamp connector from the 52 Maintenance7.Use the handle to slowly pull the lamp out of Resetting the lamp timer Status & Description IndicatorsPower events LightTroubleshooting Projector specifications SpecificationsM4 x 8 Max L = 8 mm DimensionsCeiling mount installation Ceiling Mount screwTiming chart Supported timing for PC inputUXGA 60 Specifications Supported timing for HDMI HDCP inputTiming Supported timing for Component-YPbPr inputSupported timing for Video and S-Videoinputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright