Samsung SWL-4000AP manual Select Save and reboot

Page 74

Enter the current password (Max. 30 characters) after “Enter current password (Max. 30 characters):”. Then, press [ENTER : ↵ ].

Enter the new password (Max. 30 characters) after “Enter new password (Max. 30 characters):” . Then, press [ENTER : ↵ ].

Enter the new password again after “Enter new password again:”. Then,

press [ENTER : ↵ ].

Notice : Please keep this password at a safe place or keep it where it may not get lost.

⑩You must select “Save and reboot” on [ROOT] menu, after changing the appropriate parameters by entering the new values.

==================================================

Samsung SWL-4000AP Configuration

==================================================

[ ROOT ]
1.	Basic	[Menu]
2. Advanced		[Menu]
3.	Server	[Menu]
4.	Status	[Menu]
5.	Load default values
6.	Save and reboot

Select Save and reboot

CMD(t,p,h): 6 ↵

By selecting the above menu, rebooting will occur automatically. The modified parameters of the AP will be changed effectively after it is rebooted. After the rebooting, you will view the following window to ask the password. If no further changes are needed in your settings, you do not need to enter the password.

70

Image 74

Contents SWL-4000AP Series Access Point User’s Guide Models subjected to this User’s Guide Table of Contents Appendix Ⅰ Introduction Page Installation SWL-4000APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Enter the Same Essid Channel of two APs in PTP Mode Confirm PTPPage Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Management Box Bridge Table and Protocol Management Using AP ManagerProtocol Page Select Enabled Select Protocol Which You Do Not Want NAT Setting Using AP Manager Select Server Tab NAT Setting IP Address Subnet Mask SettingConfirm NAT Setting Confirm NAT Setting Page Page Dhcp Server Setting Using AP Manager Select ServerSelect Empty Delete Current IP Allocation Table Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Adsl and Cable Modem Connection Setting Using AP Manager Select on Menu Bar Select on Dialogue BoxSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Select Encryption Confirm Selected Slot Encryption Setting Using AP ManagerConfirm Selected Slot Start Encryption Setting Page Confirm 6440-bit Bit Encryption Confirm Slot a Encryption Setting User Access Control Setting Using AP Manager User Access Control Setting Deny PassSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Line Setting Scope of Number of Packet Transmitted per SecondSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Commun-ication Page Page AP Basic Setting Using RS-232CCOM Port MagicLAN / MagicLANEnter new Dhcp Client enable, disable disable CMDt,p,h Enter DhcpCMDt,p,h Enter Gateway Address Enter new Gateway Address CMDt,p,h Enter IP Address Enter new IP AddressCMDt,p,h Enter Subnet Mask Enter new Subnet Mask Select Advanced Select Administration Select Save and reboot AP1 / AP2 Load default values Using RS-232CCOM Port All items were set to the default valuesFirmware Upgrade Using RS-232CCOM Port Via serial CMDt,p,hApfirm Page Page Explanation of Basic Configuration to use AP Manager Appendix ⅠMenu Bar List Box Dialogue Box Button BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page Appendix Ⅱ. Specification GeneralManagement Features Environmental Information We value your feedback