Samsung SWL-4000AP manual Management Features

Page 87

 

 

Management Features

 

 

 

 

Local Configuration

 

 

Serial EIA-232

 

 

 

 

Remote Configuration

 

 

- HTTP, Telnet, SNMP supported

 

 

- AP Manager for Microsoft Windows 95/98/2000/NT

 

 

 

 

 

 

 

Firmware Upgrade

 

 

Upgrading via Serial/Ethernet Interface supported

 

 

 

 

Automatic Searching AP

 

Easy to search the AP using AP Manager without

 

knowing AP's IP Address

 

 

 

SNMP Compliance

 

 

MIB I, II and 802.11 MIB

 

 

 

 

IP Sharing

 

 

- Supports NAT (Network Address Translation)

 

 

- All stations can share single IP address

 

 

 

 

 

 

 

IP Auto-configuration

 

 

Supports DHCP Server/Client features

 

 

 

 

 

 

Other Supported Features

 

 

 

 

Wireless Bridging

 

 

Extends wireless networking using wireless bridging

 

 

 

 

Filtering

 

 

Ethernet Frame Type Filtering

 

 

 

 

Access Control

 

 

Ethernet Address Filtering

 

 

 

 

Max. Associations

 

 

Limits the maximum number of stations for

 

 

load-balancing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Radio Data

 

 

 

 

 

 

 

- 2.4 GHz ISM band (2.400-2.4835 GHz)

Radio

 

 

- 11 Channels (US, Canada)

 

 

- 13 Channels (ETSI, Korea)

 

 

 

 

 

 

- 14 Channels (JAPAN)

 

 

 

 

Receiver Sensitivity

 

 

-84dBm at 11Mbps

 

 

 

 

Cell Coverage*

 

 

- Up to 150m(500ft) in Open Space

 

 

- Up to 30m(100ft) in Office Environment

 

 

 

 

 

 

 

Output Power

 

 

Typical. 17dBm(70mW)

 

 

 

 

*Cell Coverage may vary depending upon RF environment.

83

Page 86 Page 88
Image 87
Page 86 Page 88
Contents SWL-4000AP Series Access Point User’s Guide Models subjected to this User’s Guide Table of Contents Appendix Ⅰ Introduction Page Installation SWL-4000APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Confirm PTP Enter the Same Essid Channel of two APs in PTP ModePage Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Bridge Table and Protocol Management Using AP Manager ProtocolManagement Box Page Select Enabled Select Protocol Which You Do Not Want Select Server Tab NAT Setting IP Address Subnet Mask Setting NAT Setting Using AP ManagerConfirm NAT Setting Confirm NAT Setting Page Page Select Server Dhcp Server Setting Using AP ManagerSelect Empty Delete Current IP Allocation Table Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Select on Menu Bar Select on Dialogue Box Adsl and Cable Modem Connection Setting Using AP ManagerSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Encryption Setting Using AP Manager Confirm Selected Slot Start Encryption SettingSelect Encryption Confirm Selected Slot Page Confirm 6440-bit Bit Encryption Confirm Slot a Encryption Setting User Access Control Setting Deny Pass User Access Control Setting Using AP ManagerSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Scope of Number of Packet Transmitted per Second Line SettingSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Commun-ication Page Page MagicLAN / MagicLAN AP Basic Setting Using RS-232CCOM PortCMDt,p,h Enter Dhcp Enter new Dhcp Client enable, disable disableCMDt,p,h Enter IP Address Enter new IP Address CMDt,p,h Enter Subnet Mask Enter new Subnet MaskCMDt,p,h Enter Gateway Address Enter new Gateway Address Select Advanced Select Administration Select Save and reboot AP1 / AP2 All items were set to the default values Load default values Using RS-232CCOM PortVia serial CMDt,p,h Firmware Upgrade Using RS-232CCOM PortApfirm Page Page Appendix Ⅰ Explanation of Basic Configuration to use AP ManagerList Box Dialogue Box Button Bar Menu BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page General Appendix Ⅱ. SpecificationManagement Features Environmental Information We value your feedback
Top Page Image Contents