Samsung SWL-4000AP manual Environmental Information

Page 88

Environmental Information

 

Operating Temperature

0℃ to 45℃

(32℉ to 113℉)

 

 

 

 

 

Storage Temperature

-25℃to 70℃

(-13℉to 158℉)

 

 

 

 

Humidity

95% Non-condensing

 

 

 

 

 

Physical Characteristics

 

 

 

WLAN Interface

 

PCMCIA Release 2.1 (3.3V)

 

 

Wired Network Connection

10/100BaseT (RJ-45)

Type

 

 

 

Serial Interface

 

EIA-232

 

 

 

Antenna Type

 

- Two Printed Antenna within wireless LAN card

 

- Optional External Dipole Antenna

 

 

 

 

 

LED Indicator

 

Power, Ethernet Link, Wireless A, and Wireless B

 

 

 

Power Consumption

 

DC 5V, 1.23A

 

 

 

Dimension

 

250 x 153 x 40 (mm) (9.84" x 6.02" x 1.57")

 

(Except the External Dipole Antenna)

 

 

 

 

 

Weight

 

669g (1.47lb, Including the Power Adapter,

 

Excluding the Wireless LAN Card

 

 

and the External Dipole Antenna)

Notice : The specifications can be changed without a prior notice.

84

Page 87 Page 89
Image 88
Page 87 Page 89
Contents SWL-4000AP Series Access Point User’s Guide Models subjected to this User’s Guide Table of Contents Appendix Ⅰ Introduction Page Installation SWL-4000APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Enter the Same Essid Channel of two APs in PTP Mode Confirm PTPPage Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Protocol Bridge Table and Protocol Management Using AP ManagerManagement Box Page Select Enabled Select Protocol Which You Do Not Want NAT Setting Using AP Manager Select Server Tab NAT Setting IP Address Subnet Mask SettingConfirm NAT Setting Confirm NAT Setting Page Page Dhcp Server Setting Using AP Manager Select ServerSelect Empty Delete Current IP Allocation Table Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Adsl and Cable Modem Connection Setting Using AP Manager Select on Menu Bar Select on Dialogue BoxSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Confirm Selected Slot Start Encryption Setting Encryption Setting Using AP ManagerSelect Encryption Confirm Selected Slot Page Confirm 6440-bit Bit Encryption Confirm Slot a Encryption Setting User Access Control Setting Using AP Manager User Access Control Setting Deny PassSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Line Setting Scope of Number of Packet Transmitted per SecondSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Commun-ication Page Page AP Basic Setting Using RS-232CCOM Port MagicLAN / MagicLANEnter new Dhcp Client enable, disable disable CMDt,p,h Enter DhcpCMDt,p,h Enter Subnet Mask Enter new Subnet Mask CMDt,p,h Enter IP Address Enter new IP AddressCMDt,p,h Enter Gateway Address Enter new Gateway Address Select Advanced Select Administration Select Save and reboot AP1 / AP2 Load default values Using RS-232CCOM Port All items were set to the default valuesFirmware Upgrade Using RS-232CCOM Port Via serial CMDt,p,hApfirm Page Page Explanation of Basic Configuration to use AP Manager Appendix ⅠMenu Bar List Box Dialogue Box Button BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page Appendix Ⅱ. Specification GeneralManagement Features Environmental Information We value your feedback
Top Page Image Contents