Samsung SWL-4000AP manual Firmware Upgrade Using RS-232CCOM Port, Via serial CMDt,p,h

Page 77

20.Firmware Upgrade Using RS-232C(COM Port)

①Click the “Hyperterminal icon” saved in hard disk of your PC’

②“Enter password” menu will be displayed on the HyperTerminal window. The default password is “public”,

③When the password is entered, [ROOT] menu appears on the HyperTerminal window.

④Downloaded the latest version of AP firmware in local disk of your PC

Notice: AP firmware corresponding to your AP can be downloaded in MagicLAN home page.

⑤After selecting [Advanced] menu on [ROOT] menu, select [Upgrade FW via serial] menu on [Advanced] menu again

==================================================

Samsung SWL-4000AP Configuration

==================================================

[ Advanced ]
1.	Radio	[Menu]
2.	Encryption	[Menu]
3.	HTTP Activity	Enabled
4. Telnet Activity		Enabled
5. Administration		[Menu]
6.	Upgrade FW via serial	Select Upgrade FW
6.	Upgrade FW via serial

via serial

CMD(t,p,h): 6 ↵

73

Image 77

Contents SWL-4000AP Series Access Point User’s Guide Models subjected to this User’s Guide Table of Contents Appendix Ⅰ Introduction Page Installation SWL-4000APDA AP Basic Setting Using AP Manager Page Page Confirm New Configuration Resetting to Default Values PTP Setting Using AP Manager Page Confirm PTP Enter the Same Essid Channel of two APs in PTP ModePage Confirm PTP Mode Setting AML Setting Using AP Manager Page Enter the Same Essid Channel of all APs in AML Mode Confirm AML Mode Setting Management Box Bridge Table and Protocol Management Using AP ManagerProtocol Page Select Enabled Select Protocol Which You Do Not Want Select Server Tab NAT Setting IP Address Subnet Mask Setting NAT Setting Using AP ManagerConfirm NAT Setting Confirm NAT Setting Page Page Select Server Dhcp Server Setting Using AP ManagerSelect Empty Delete Current IP Allocation Table Confirm Dhcp Server Setting Confirm Dhcp Server Setting Page NAT and Dhcp Server Simultaneous Setting Using AP Manager Confirm NAT Dhcp Setting Confirm NAT Setting Confirm Dhcp Server Setting Select on Menu Bar Select on Dialogue Box Adsl and Cable Modem Connection Setting Using AP ManagerSettings for Adsl PPPoE Dhcp Server NAT Setting Connected Disconnected Negotiating Settings for Adsl Pptp Setting Dhcp Server and NAT Connected Disconnected Negotiating Settings for Cable Modem Page Select Encryption Confirm Selected Slot Encryption Setting Using AP ManagerConfirm Selected Slot Start Encryption Setting Page Confirm 6440-bit Bit Encryption Confirm Slot a Encryption Setting User Access Control Setting Deny Pass User Access Control Setting Using AP ManagerSelect Connection Deny Select Connection Permit Move MAC ID Save MAC ID File name.lst Page Firmware Upgrade Using AP Manager File Icon Page Data Transmission Status Check Using AP Manager Scope of Number of Packet Transmitted per Second Line SettingSelect MIB Type Related Information Confirm Box AP Setting Using Web Browser Page AP Setting Using Telnet HyperTerminal Setting for RS-232CCOM Port Commun-ication Page Page MagicLAN / MagicLAN AP Basic Setting Using RS-232CCOM PortCMDt,p,h Enter Dhcp Enter new Dhcp Client enable, disable disableCMDt,p,h Enter Gateway Address Enter new Gateway Address CMDt,p,h Enter IP Address Enter new IP AddressCMDt,p,h Enter Subnet Mask Enter new Subnet Mask Select Advanced Select Administration Select Save and reboot AP1 / AP2 All items were set to the default values Load default values Using RS-232CCOM PortVia serial CMDt,p,h Firmware Upgrade Using RS-232CCOM PortApfirm Page Page Appendix Ⅰ Explanation of Basic Configuration to use AP ManagerList Box Dialogue Box Button Bar Menu BarAdsl Connection Status AP Search Erase Window AP Search Cycle Page General Appendix Ⅱ. SpecificationManagement Features Environmental Information We value your feedback