Samsung RNX-EASYN4 user manual Appendix B IC Interference Statement, Industry Canada statement

Page 110

Wireless Router RNX-EasyN4		User Manual

Appendix B – IC Interference Statement

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

Thank you for purchasing a quality Rosewill Product.

Please register your product at : www.rosewill.com for complete warranty information and future support for your product.

Image 110

Contents Wireless Router RNX-EasyN4 Table of Contents Introduction Key Features Features AdvantagesPackage Contents Product Layout LED Internet RNX-EASYN4 Placement Network + System RequirementsSetup LAN, WAN PC Network Adapter setup Windows XP Wireless Router RNX-EasyN4 Bring up RNX-EASYN4 Smart WizardWireless Router RNX-EasyN4 Click Next to proceed. Click Exit to abort Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Again Click Next to configure WAN & Wireless settings Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 To apply the entire configuration, click Reboot Initial Setup RNX-EASYN4 Login ProcedureWireless Router RNX-EasyN4 AP Router Mode StatusWireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 LAN LAN IP Dhcp ServerDhcp Schedule Wireless Router RNX-EasyN4 Event Log Monitor Language „ Wizard „ Internet Dynamic IPStatic IP Point-to-Point over Ethernet Protocol PPPoE Point-to-Point Tunneling Protocol Pptp „ Wireless Settings BasicWireless Router RNX-EasyN4 WDS with AP Router Advanced Wireless Router RNX-EasyN4 Security Enable 802.1x Authentication WEP EncryptionWireless Router RNX-EasyN4 WPA Pre-Shared Key Encryption WPA-Radius Encryption MAC Address Filtering Remove an address from the list Wi-Fi Protected Setup WPSAdding an address into the list Wireless Router RNX-EasyN4 Client List Policy „ Firewall Settings Advanced Demilitarized Zone DMZ Denial of Service DoS MAC Filter Wireless Router RNX-EasyN4 Add PC MAC Address Remove PC MAC AddressRemove PC IP Address IP FilterAdd PC IP Address URL Filter Add URL KeywordRemove URL Keyword „ Advanced Settings Network Address Translation NATPort Mapping Remove Port Mapping Port Forwarding Virtual ServerAdd Port Mapping Wireless Router RNX-EasyN4 Add Port Forwarding Remove Port ForwardingPort Triggering Special Applications Add Port Triggering Remove Port TriggeringApplication Layer Gateway ALG UpnpQuality of Service QoS Priority Queue Bandwidth Allocation Routing „ Tools Settings AdminRemote management Time Setup TimeSynchronize with the NTP server Ddns Power Diagnosis Firmware Back-up Reset Wireless Router RNX-EasyN4 Repeater Mode „ SystemLAN Schedule Wireless Router RNX-EasyN4 Event Log Monitor „ Wireless Wireless Router RNX-EasyN4 Clint List Communication between Wireless clients „ Tools Remote management Time Synchronize with PC Power Diagnosis Wireless Router RNX-EasyN4 Back-up Reset Appendix a FCC Interference Statement Federal Communication Commission Interference StatementAppendix B IC Interference Statement Industry Canada statement