Samsung RNX-EASYN4 user manual Wireless Router RNX-EasyN4

Page 49

Wireless Router RNX-EasyN4

User Manual

 

 

 

 

 

 

Authentication Type: There are two authentication types: "Open System" and "Shared Key". When you select "Open System", wireless stations can associate with this wireless router without WEP encryption. When you select "Shared Key", you should also setup a WEP key in the "Encryption" page. After this has been done, make sure the wireless clients that you want to connect to the device are also setup with the same encryption key.

Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit. The larger the key will be the higher level of security is used, but the throughput will be lower.

Key Type: You may select ASCII Characters (alphanumeric format) or Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the WEP Key.

Key1 - Key4: The WEP keys are used to encrypt data transmitted in the wireless network. Use the following rules to setup a WEP key on the device.

Image 49
Contents Wireless Router RNX-EasyN4 Table of Contents Introduction Features Advantages Key FeaturesPackage Contents Product Layout LED Internet Network + System Requirements RNX-EASYN4 PlacementSetup LAN, WAN PC Network Adapter setup Windows XP Wireless Router RNX-EasyN4 Smart Wizard Bring up RNX-EASYN4Wireless Router RNX-EasyN4 Click Next to proceed. Click Exit to abort Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Again Click Next to configure WAN & Wireless settings Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 To apply the entire configuration, click Reboot Login Procedure Initial Setup RNX-EASYN4Wireless Router RNX-EasyN4 Status AP Router ModeWireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 LAN Dhcp Server LAN IPDhcp Schedule Wireless Router RNX-EasyN4 Event Log Monitor Language „ Wizard Dynamic IP „ InternetStatic IP Point-to-Point over Ethernet Protocol PPPoE Point-to-Point Tunneling Protocol Pptp Basic „ Wireless SettingsWireless Router RNX-EasyN4 WDS with AP Router Advanced Wireless Router RNX-EasyN4 Security WEP Encryption Enable 802.1x AuthenticationWireless Router RNX-EasyN4 WPA Pre-Shared Key Encryption WPA-Radius Encryption MAC Address Filtering Adding an address into the list Wi-Fi Protected Setup WPSRemove an address from the list Wireless Router RNX-EasyN4 Client List Policy „ Firewall Settings Advanced Demilitarized Zone DMZ Denial of Service DoS MAC Filter Wireless Router RNX-EasyN4 Remove PC MAC Address Add PC MAC AddressAdd PC IP Address IP FilterRemove PC IP Address Add URL Keyword URL FilterRemove URL Keyword Network Address Translation NAT „ Advanced SettingsPort Mapping Add Port Mapping Port Forwarding Virtual ServerRemove Port Mapping Wireless Router RNX-EasyN4 Remove Port Forwarding Add Port ForwardingPort Triggering Special Applications Remove Port Triggering Add Port TriggeringUpnp Application Layer Gateway ALGQuality of Service QoS Priority Queue Bandwidth Allocation Routing Admin „ Tools SettingsRemote management Time Time SetupSynchronize with the NTP server Ddns Power Diagnosis Firmware Back-up Reset Wireless Router RNX-EasyN4 „ System Repeater ModeLAN Schedule Wireless Router RNX-EasyN4 Event Log Monitor „ Wireless Wireless Router RNX-EasyN4 Clint List Communication between Wireless clients „ Tools Remote management Time Synchronize with PC Power Diagnosis Wireless Router RNX-EasyN4 Back-up Reset Federal Communication Commission Interference Statement Appendix a FCC Interference StatementIndustry Canada statement Appendix B IC Interference Statement