Samsung user manual Bring up RNX-EASYN4, Smart Wizard

Page 13

Wireless Router RNX-EasyN4		User Manual

8 Bring up RNX-EASYN4

Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, RNX-EASYN4 automatically enters the self-test phase. During self-test phase, Power LED will blink briefly, and then will be lit continuously to indicate that this product is in normal operation.

9 Smart Wizard

CHECK

•Internet connection should be setup & ready to use (ADSL or cable modem).

•Modem must provide RJ45 port to connect with RNX-EASYN4.

•Microsoft Windows compatible PC/Notebook with UPnP enabled network adapter

•CAT 5 network cable(s), RJ45 port on PC/Notebook.

STEP 1

Connect RNX-EASYN4 WAN port & your modem WAN port with RJ45 cable.

STEP 2

Power up RNX-EASYN4.POWER led on front panel lights up & remains stable.

STEP 3

Connect RNX-EASYN4 LAN port & PC/Notebook RJ45 port with network cable.

Click on this icon to run SMART WIZARD.

Image 13

Contents Wireless Router RNX-EasyN4 Table of Contents Introduction Features Advantages Key FeaturesPackage Contents Product Layout LED Internet Network + System Requirements RNX-EASYN4 PlacementSetup LAN, WAN PC Network Adapter setup Windows XP Wireless Router RNX-EasyN4 Smart Wizard Bring up RNX-EASYN4Wireless Router RNX-EasyN4 Click Next to proceed. Click Exit to abort Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Again Click Next to configure WAN & Wireless settings Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 To apply the entire configuration, click Reboot Login Procedure Initial Setup RNX-EASYN4Wireless Router RNX-EasyN4 Status AP Router ModeWireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 LAN Dhcp Server LAN IPDhcp Schedule Wireless Router RNX-EasyN4 Event Log Monitor Language „ Wizard Dynamic IP „ InternetStatic IP Point-to-Point over Ethernet Protocol PPPoE Point-to-Point Tunneling Protocol Pptp Basic „ Wireless SettingsWireless Router RNX-EasyN4 WDS with AP Router Advanced Wireless Router RNX-EasyN4 Security WEP Encryption Enable 802.1x AuthenticationWireless Router RNX-EasyN4 WPA Pre-Shared Key Encryption WPA-Radius Encryption MAC Address Filtering Adding an address into the list Wi-Fi Protected Setup WPSRemove an address from the list Wireless Router RNX-EasyN4 Client List Policy „ Firewall Settings Advanced Demilitarized Zone DMZ Denial of Service DoS MAC Filter Wireless Router RNX-EasyN4 Remove PC MAC Address Add PC MAC AddressAdd PC IP Address IP FilterRemove PC IP Address Add URL Keyword URL FilterRemove URL Keyword Network Address Translation NAT „ Advanced SettingsPort Mapping Add Port Mapping Port Forwarding Virtual ServerRemove Port Mapping Wireless Router RNX-EasyN4 Remove Port Forwarding Add Port ForwardingPort Triggering Special Applications Remove Port Triggering Add Port TriggeringUpnp Application Layer Gateway ALGQuality of Service QoS Priority Queue Bandwidth Allocation Routing Admin „ Tools SettingsRemote management Time Time SetupSynchronize with the NTP server Ddns Power Diagnosis Firmware Back-up Reset Wireless Router RNX-EasyN4 „ System Repeater ModeLAN Schedule Wireless Router RNX-EasyN4 Event Log Monitor „ Wireless Wireless Router RNX-EasyN4 Clint List Communication between Wireless clients „ Tools Remote management Time Synchronize with PC Power Diagnosis Wireless Router RNX-EasyN4 Back-up Reset Federal Communication Commission Interference Statement Appendix a FCC Interference StatementIndustry Canada statement Appendix B IC Interference Statement