Samsung RNX-EASYN4 user manual Wireless Router RNX-EasyN4

Page 46

Wireless Router RNX-EasyN4		User Manual

Beacon Interval: is the interval of time that this wireless router broadcasts a beacon. A Beacon is used to synchronize the wireless network.

DTIM Period: Enter a value between 1 and 255 for the Delivery Traffic Indication Message (DTIM). A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages

Data Rate: The “Data Rate” is the rate that this access point uses to transmit data packets. The access point will use the highest possible selected transmission rate to transmit the data packets.

N Data Rate: The “Data Rate” is the rate that this access point uses to transmit data packets for N compliant wireless nodes. Highest to lowest data rate can be fixed.

Channel Bandwidth: This is the range of frequencies that will be used.

Preamble Type: The “Long Preamble” can provide better wireless LAN compatibility while the “Short Preamble” can provide better wireless LAN performance.

CTS Protection: It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to a lot of frame-network that is transmitted.

TX Power: This can be set to a bare minimum or maximum power.

Image 46

Contents Wireless Router RNX-EasyN4 Table of Contents Introduction Key Features Features AdvantagesPackage Contents Product Layout LED Internet RNX-EASYN4 Placement Network + System RequirementsSetup LAN, WAN PC Network Adapter setup Windows XP Wireless Router RNX-EasyN4 Bring up RNX-EASYN4 Smart WizardWireless Router RNX-EasyN4 Click Next to proceed. Click Exit to abort Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Again Click Next to configure WAN & Wireless settings Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 To apply the entire configuration, click Reboot Initial Setup RNX-EASYN4 Login ProcedureWireless Router RNX-EasyN4 AP Router Mode StatusWireless Router RNX-EasyN4 Wireless Router RNX-EasyN4 LAN LAN IP Dhcp ServerDhcp Schedule Wireless Router RNX-EasyN4 Event Log Monitor Language „ Wizard „ Internet Dynamic IPStatic IP Point-to-Point over Ethernet Protocol PPPoE Point-to-Point Tunneling Protocol Pptp „ Wireless Settings BasicWireless Router RNX-EasyN4 WDS with AP Router Advanced Wireless Router RNX-EasyN4 Security Enable 802.1x Authentication WEP EncryptionWireless Router RNX-EasyN4 WPA Pre-Shared Key Encryption WPA-Radius Encryption MAC Address Filtering Adding an address into the list Wi-Fi Protected Setup WPSRemove an address from the list Wireless Router RNX-EasyN4 Client List Policy „ Firewall Settings Advanced Demilitarized Zone DMZ Denial of Service DoS MAC Filter Wireless Router RNX-EasyN4 Add PC MAC Address Remove PC MAC AddressAdd PC IP Address IP FilterRemove PC IP Address URL Filter Add URL KeywordRemove URL Keyword „ Advanced Settings Network Address Translation NATPort Mapping Add Port Mapping Port Forwarding Virtual ServerRemove Port Mapping Wireless Router RNX-EasyN4 Add Port Forwarding Remove Port ForwardingPort Triggering Special Applications Add Port Triggering Remove Port TriggeringApplication Layer Gateway ALG UpnpQuality of Service QoS Priority Queue Bandwidth Allocation Routing „ Tools Settings AdminRemote management Time Setup TimeSynchronize with the NTP server Ddns Power Diagnosis Firmware Back-up Reset Wireless Router RNX-EasyN4 Repeater Mode „ SystemLAN Schedule Wireless Router RNX-EasyN4 Event Log Monitor „ Wireless Wireless Router RNX-EasyN4 Clint List Communication between Wireless clients „ Tools Remote management Time Synchronize with PC Power Diagnosis Wireless Router RNX-EasyN4 Back-up Reset Appendix a FCC Interference Statement Federal Communication Commission Interference StatementAppendix B IC Interference Statement Industry Canada statement