Samsung 913V manual Symptom, Check List, Can you see Check Signal Cable on the screen?, Solutions

Page 40

Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.

Symptom

No images on the screen. I cannot turn on the monitor.

Check List

Is the power cord connected properly?

Can you see "Check Signal Cable" on the screen?

If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.

Can you see "Not Optimum

Mode","Recommanded Mode 1280 x 1024 60Hz" on the screen?

There is no image on the screen.

Is the power indicator on the monitor blinking at 1 second

Solutions

Check the power cord connection and supply.

Check the signal cable connection.

If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes)

Note: If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.

You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.

Adjust the maximum resolution and frequency that the monitor can handle properly.

If the display exceeds SXGA or 75Hz, a

"Not Optimum Mode","Recommanded Mode 1280 x 1024 60Hz" message is displayed. If the display exceeds 85Hz, the display will work properly but the "Not

Optimum Mode","Recommanded Mode 1280 x 1024 60Hz" message appears for one minute and then disappears.

Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.)

The monitor is in PowerSaver mode.

press a key on the keyboard to activate the monitor and restore the image on

Image 40

Contents SyncMaster Power Do not use a damaged or loose plugInstallation Insert the power plug firmly so that it does not come looseDo not drop the monitor when moving it Use only a properly grounded plug and receptacleKeep any heating devices away from the power cable Do not place the product on the floorSet down the monitor carefully Do not place the monitor face downClean Do not spray water or detergent directly on the monitorOthers Do not remove cover or backDo not cover the vents on the monitor cabinet Never insert anything metallic into the monitor openingsFalling product could cause physical damage even death Unpacking Front Rear Sub 15-pin portMonitor Assembly Attaching a base Click Windows XP/2000 Driver Windows XP/2000Microsoft Windows XP Operating System Page Page Microsoft Windows NT Operating System How to install Click Start , Setting , Control PanelLinux Operating System Natural Color How to install the Natural Color softwareNatural Color Software Program Auto Menu MagicBrightDescription Brightness Adjust BrightnessPicture Color ImageDescription Play/Stop Color Tone Color Control GammaOSD Coarse Fine Sharpness PositionInformation SetupLanguage Position Transparency Display Time Shows a video source, display mode on the OSD screen OSD Mode What is MagicTune?Basic Functionality Installation Page Installationation Problems Hardware Button Tab Definition Picture Tab DefinitionColor Tab Definition BrightnessImage Tab Definition Color ToneImage Setup Option Tab DefinitionSupport Tab Definition PreferencesColor Calibration PreviewPage Uninstall Troubleshooting Symptom Can you see Check Signal Cable on the screen?Mode,Recommanded Mode 1280 x 1024 60Hz on the screen? SolutionsRefer to the Preset Timing Modes Panel → Display → SettingsSelf-Test Feature Check Useful Tips General PowerSaver Preset Timing ModesHorizontal Frequency Vertical FrequencyService Australia BrazilGermany Portugal United KingdomTerms For Better DisplayAuthority User Information FCC Information User InstructionsIC Compliance Notice Why do we have environmentally-labelled monitors? MPR II ComplianceEuropean NoticeEurope Only PCT NoticeWhat does labelling involve? Environmental RequirementsLead CadmiumCFCs freons Why do we have environmentally labelled computers?TCO Development Environmental requirements Flame retardants ErgonomicsEnergy EmissionsEcology TCO03 Recycling Information TCO03 applied model onlyVideo In / RS 232 / Video Out Transport and Storage LimitationsPower Off, Screen Saver, or Power Save Mode What is Image retention ?Suggestions for specific applications