Mitsubishi Electronics DX-TL5000U user manual Countermeasure Cancelling Log number

Warning Display

No Camera Signal

Camera signal is lost or distorted. Please check the camera and cable connection.

Countermeasure	Cancelling Log number	CALL OUT
		output
	the warning	#1
• Check whether the unit	Stop recording. LOG54 #7	Fixed
and camera are properly
connected, and that electri
-city is on.
• Check whether the video	Output video
signal is being properly	signals.
outputted.
• Check to see if there is a	Click "Clear
camera set for operation	Warning" or
with no video signal input.	press the E
	button.

It can use as it is though a slight error		• Continue the operation		LOG13	#8	None
occurred.		when there is no abnormality.		LOG23	#8
		• When the error occurs		LOG33	#8
		continuously, check the		LOG43	#8
		HDD/media, cable and		LOG73	#8
		termination and restart the unit.
System suspended due to unstable		• Restart the unit.	Click "Clear	LOG14	#8	Fixed
processing. Recording will be resumed.			Warning" or
HDD	was disconnected.		press the E
System suspended due to unstable processing.			button.	LOG24	#8	None
Start operation again.				LOG34	#8
				LOG44	#8
				LOG74	#8
The alteration part is found in the data.			Click "Clear	LOG55	#7	None
			Warning" or
			press the E
			button.
Recorder detected technical problems			Click "Clear	LOG6200		Fixed
on the device.			Warning" or
			press the E
			button.
The recorder has been rebooted. The problem		• Check the unit.	Click "Clear	LOG5100		Fixed
is not critical, but check the recorder.			Warning" or
			press the E
			button.
Internal temperature is getting too high,		• Turn off the power and	Click "Clear	LOG5200		Fixed
check the ventilation of the recorder.		change the installation	Warning" or
		condition.	press the E
			button.
Internal temperature is getting too high,		• Turn off the power and	Click "Clear	LOG5201		Fixed
stop the operation of the recorder		change the installation	Warning" or
immediately.		condition.	press the E
			button.
			Lower the
			temperature.
The fan of the recorder needs to be checked.		• Turn off the power and	Click "Clear	LOG5300		Fixed
		stop using.	Warning" or
			press the E
			button.
			Rotate the fan.
Copying data stopped because of new record		• Stop HDD recording to	Click "Clear	LOG3500#3		None
overwrites the old data.		continue copy/archive.	Warning" or	LOG7500#4
			press the E
			button.
New record will soon overwrite the old data		• Stop HDD recording to	Click "Clear	LOG3600#3		None
in copying.		continue copy/archive.	Warning or	LOG7600#4
Stop the recording, if you want to continue the		• Stop copy/archive to	press the E
copying.		continue HDD recording.	button.
(none)		• Restarts by watchdog		LOG5101		–
		operation.

#8 : 14	: Recording	24	: Playback
34	: Copy 1	44	: Restore		74 : Copy 2
(The following numbers are in				)
00	: A (Internal)	01 : B (Internal)			02 : C (Internal)
03	: D (Internal)	10 to 26 : USB (External)

30 to 35 : SCSI (External) 40 to 47 : NAS (External)

Regarding LOG1400: Displays during recording. The system shuts down once and then resumes recording. (The error HDD is automatically deleted from the registration for the recording device. The recording is continued until all the registered HDDs are used up.)

Regarding LOG24 to 74: Displays during copying or playback. The playback or copy stops because the system shuts down. Carry out playback or copy again.

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Warnings and CALL OUT output

35