Mitsubishi Electronics 148 Series, 246 Series Setup to Control Switching to the TV’s Audio Output

Page 64

646. NetCommand IR Control

Setting Up NetCommand Control of an A/V Receiver, continued

example, use an optional audio connection if you wish to use the A/V receiver speakers to hear audio from:

-- The ANT 1 or ANT 2 inputs

-- A device connected to the convenience input (input 4), such as a game or camcorder.

In some circumstances, audio from a device con- nected to the A/V receiver may not be passed over the HDMI cable to the TV speakers. You must use the A/V receiver speakers to hear audio in these cases.

Before You Begin

To complete these steps you will need:

The remote controls for both the TV and the A/V receiver.

The IR emitter cable supplied with the TV.

An HDMI-to-HDMI cable to connect the A/V receiver to the TV and cables necessary to connect devices to the A/V receiver.

1.Connect your audio/video devices to the A/V receiver. Note the name of the device connected to each A/V receiver input. This information will be needed later to set up NetCommand’s automatic input switching.

2.Connect the A/V receiver to the TV with an HDMI- to-HDMI cable.

3.Connect the IR emitter cable to the TV and position the IR emitter where it can send signals to the A/V receiver. See “IR Emitter Placement,” page 55.

4.Power on the A/V receiver.

5.Set the TV’s remote control slide switch to the TV position and power on the TV if needed.

1

4

3

2

6.When the Auto Input Sensing screen displays, select device name AVR.

Setup to Control A/V Receiver Power and Volume

Perform the steps under “A/V Receiver Control: Power and Volume,” page 60.

Setup to Control Switching to the TV’s Audio Output

If you have used one of the optional audio connec- tions to the TV’s AVR AUDIO OUTPUT or DIGITAL AUDIO OUTPUT jacks, set up NetCommand to control switching to the TV audio input. Perform the steps under “Audio Switching Setup 1: Automatic A/V Receiver Switching to the TV Audio Input,” page 62.

Setup to Control Automatic Audio and Video Switching via HDMI

Follow these steps if you wish NetCommand to control switching of A/V receiver video as well as audio inputs. When this setup is complete, you can use the TV’s Input Selection menu to select a video device con- nected to the A/V receiver. You can also perform addi- tional NetCommand setup to control devices connected to the A/V receiver.

1.Display the Inputs > AVR menu.

Note: The labels Input1 through Input5 in the Learn column are names used by the TV to uniquely identify A/V receiver inputs.

2.With the highlight in the Learn column, highlight one of the Input labels Input2 through Input5; it is recommended you leave Input1 reserved for TV Audio.

AVR menu for audio and video switching with HDMI output

1The Learn column lists “learnable” keys from the A/V receiver’s remote control.

2Input1 through Input5 are arbitrary names used by the TV to uniquely identify “learnable” A/V receiver inputs.

3A check mark next to a key name indicates it has been “learned” by NetCommand.

4The Assign Input column provides a list of possible device types. Use this list to

select the device type connected to the associated A/V receiver input. The assigned device name will appear in the Input Selection menu.

Image 64
Contents LT-40148, LT-46148, LT-52148 LT-46246, LT-52246Refer Servicing to Qualified Service Personnel For Your RecordsContents Replacement Parts Outdoor Antenna GroundingInstallation Notes Cleaning Recommendations TV Guide Daily Access RequirementsIf Your TV Gets Damaged Disposal of Your TVPackage Contents Special Features of Your TVTV Control Panel Convenience Inputs TV Guide Daily Interactive Program Guide SystemSwivelling Stand Convenience InputsFront-Panel Indicators Power IndicatorStatus Indicator LED Color TV Condition Additional InformationTV Main Panel IR NetCommand Output/External Controller Input Hdmi Inputs High-Definition Multimedia InterfaceRS-232C Selecting Audio Output Type, 246 Series TVsStand Removal Stand-Removal ProcedureTV Back Cover Protective Sheet Guidelines for Setting Up and Using Your New Widescreen TV Installing the Remote Control BatteriesWhen You First Power On the TV Getting StartedAdditional TV Setup TV CleaningTV Operation AssistanceInitial TV Setup Setting Up TV InputsWhen You First Connect a Device Memorizing ChannelsAuto Input Sensing for CEC-Enabled Devices Setup ProcedureAuto Input/Auto Output Sensing Screens ReceiverControlling A/V Receiver Sound Volume With a Standard TV SetupWith NetCommand IR Control With NetCommand for Hdmi CEC-Enabled Hdmi A/V ReceiverSource device connected directly to the TV Connecting a Computer to the TV Computer Video Connection Audio Video OutputUsing the TV with a Personal Computer Computer Video AdjustmentsImage Resolution Computer Display FormatsUsing a CableCARD Installing a CableCARDSeries TVs CableCARD MenuInstalling the Cable Tie Before You BeginCable Management Cable RoutingCable service or Hdmi and Audio SignalsIncoming from Satellite dishCables to Input Connect audioAudio Antennas with Separate UHF and VHF Leads Wall Outlet Cable no cable boxAntenna with a Single Lead VCR to a Cable Box Audio & Video VCR to an Antenna or Wall Outlet CableVCR Older Cable Box 26 3. TV ConnectionsReceiver Sound System Using the TV’s Audio Output Camcorder Audio-Only DevicePb Pr Component Video Connection Composite Video ConnectionChoosing a Viewing Source Sleep TimerTV Tips Cancel Remote Control23. F1-F4 For devices under NetCommand control ChannelView Channel Listings Signal Strength Status DisplayAnt 1 TV-PG FAV1Fav Favorite Channels ANT-1TV Signals and Display Formats Signal DefinitionsDVD Image Definitions TV Display Format DefinitionsJpeg Images and the USB Photo Port Viewing Camera FilesJpeg Thumbnail Menu Media Setup Menu Camera Photos and Moving Video as Composite VideoSlide Show Keys for Jpeg Picture Slide ShowRemote Control Keys for the TV Menu System Main MenuAV Menu AV Menu OptionsFilm Mode Auto, Off Video Mute On, OffGlobal Audio Only On, OffVideo Menu Video Menu OptionsVert Adjustment SharpEdge On, OffDeepField ImagerFrom the Audio menu Audio MenuAudio Menu Options Captions Menu Captions on Analog ChannelsCaptions on Digital Channels Captions Menu OptionsSetup Menu Options Setup Menu1 Enter Setup menu, Edit channel options EditClock TimeManual DateTimer Setup menu, Timer optionsEnergy Fast Power On Mode Low Power Use the External Controller Input Wired IR option seeThis page intentionally left blank Only when Inputs NetCommand Inputs MenuInput Selection menu Selection menuLock Menu Pass CodesParent Menu Other Menu Alternate Rating SystemParent Menu Options U.S.-based rating system TV-YTV-Y7 TV-GOther Menu Options alternate rating system TimeAbout NetCommand IR Control Important Note on NetCommandIR Emitter Placement An IR emitter cable is included with the TVInitial NetCommand Setup for Most Devices If the device has no Power OFF key, skip this stepGuide PowerCH/PAGE Operating NetCommand-Controlled Devices Controlling Most Device TypesControlling an A/V Receiver Special Operation MethodsInside the Guide Outside the GuideSetting Up NetCommand Control of an A/V Receiver Receiver Control Power and VolumeSetup to Control A/V Receiver Power and Volume Before You BeginReceiver Control Automatic Audio Switching Audio Switching SetupAudio Available from TV only Analog Stereo AudioAV Receiver menu to set up audio switching More About Using an Hdmi Connection with this Setup VCRSetup to Control Switching to the TV’s Audio Output AVR menu for audio and video switching with Hdmi outputNetCommand IR Control Device Connected to an A/V Receiver Ated Assign Input column Assign Input1 throughAssign Input5 Open the Inputs Learn menuAppendix a Specifications Width Depth Weight lbsAppendix B Bypassing the Parental Lock Bypassing the Parental LockThis page intentionally left blank Appendix C Programming the Remote Control Functions Available for Other A/V DevicesProgramming the Remote Control DVDCABLE/SAT VCR DVD Audio Code VerificationProgramming Codes Make CodeCable Boxes Cable Boxes Make CodeReceivers Make Code Laser Disc PlayersSatellite Receivers Make Code VCRs Make Code ABSDVD Players DVD Players Make CodeAppendices75 Initial Guide Setup Appendix D TV Guide Daily 246 Series TVsMain Guide Screen Elements High-definition ChannelIcon NumberUsing the TV Guide Daily System Setting Up TV Guide DailyNavigating the Guide Modifying the Guide Setup Looking at AdsCustomizing Guide Listings Available OptionsProcedure TV Guide Daily Troubleshooting Tips Symptom RemarksEnabling or Disabling the TV’s NetCommand Hdmi Control Appendix E NetCommand Hdmi Control of CEC DevicesConnecting Hdmi Devices to the TV Appendices81 Resetting Hdmi Control or Removing an Hdmi Device Figure Using NetCommand Hdmi ControlCEC-enabled A/V receiver functions that may be available TV Reset Comparison Guide Appendix F TroubleshootingReset Name When to Use How to Use Resulting Action Service and Customer Support ServiceRead the ON-SCREEN TionsGeneral TV Operation Symptom Remarks TV Channels Symptom RemarksTV Power On/Off Symptom Remarks Picture Symptom RemarksSymptom Remarks Indicators Symptom Remarks NetCommand IR Control Symptom RemarksAppendices89 Trademark and License Information Mitsubishi TV Software To Obtain Warranty Service This Limited Warranty does not CoverWarranty93 Index Index95 MDEAservice@mdea.com System Reset