Mitsubishi Electronics 148 Series manual Front-Panel Indicators, Power Indicator, Status Indicator

Page 8

81. Television Overview

Front-Panel Indicators

•STATUS indicator. Off during normal TV operation.

•POWER/TIMER indicator. Lit when TV is powered on; flashes when TV is powered off and the auto-on TV Timer is set.

•IR Sensor (Infrared Sensor). Detects infra- red signals emitted by the remote control.

STATUS POWER	IR Sensor

POWER STATUS

IR Sensor

148 Series TVs

246 Series TVs

	Off	Steady On		Slow Blinking	Fast Blinking

	POWER Indicator

	LED Color	TV Condition			Additional Information
	None	Standby condition.			Normal operation.
	None

	Green	TV is powered on.			Normal operation.

	Green	TV powered off, auto-on timer is set.			Normal operation. TV can be turned on at any time.

	Green	1. TV just plugged into AC outlet.			Wait approximately one minute for blinking to stop before turning
	Green	1. TV just plugged into AC outlet.			on. Normal operation.
					on. Normal operation.

2.AC just restored after power failure.

3.TV rebooting after System Reset used.

4.TV rebooting after power fluc- tuation or receiving abnormal digital signals from a digital channel or digital device.

5.You have begun the procedure to update software from an authorized flash memory device.

STATUS Indicator

LED Color	TV Condition	Additional Information
None	Normal TV on or standby condition.	Normal operation.

Red	TV may require service.	Turn off the TV and unplug the set from the AC power source.
Red		Wait one minute and then plug the set back in. See Appendix F.

		If the LED is still on, contact your dealer or a Mitsubishi
		Authorized Service Center. Go to www.mitsubishi-tv.com or call
		1-800-332-2119 to receive Authorized Service Center information.

Image 8

Contents LT-40148, LT-46148, LT-52148 LT-46246, LT-52246Refer Servicing to Qualified Service Personnel For Your RecordsContents Replacement Parts Outdoor Antenna Grounding Installation Notes Cleaning Recommendations TV Guide Daily Access Requirements If Your TV Gets Damaged Disposal of Your TVPackage Contents Special Features of Your TVTV Control Panel Convenience Inputs TV Guide Daily Interactive Program Guide SystemSwivelling Stand Convenience InputsFront-Panel Indicators Power IndicatorStatus Indicator LED Color TV Condition Additional InformationTV Main Panel IR NetCommand Output/External Controller Input Hdmi Inputs High-Definition Multimedia InterfaceRS-232C Selecting Audio Output Type, 246 Series TVsTV Back Cover Protective Sheet Stand-Removal ProcedureStand Removal Guidelines for Setting Up and Using Your New Widescreen TV Installing the Remote Control BatteriesWhen You First Power On the TV Getting StartedAdditional TV Setup TV CleaningTV Operation AssistanceInitial TV Setup Setting Up TV InputsWhen You First Connect a Device Memorizing ChannelsAuto Input Sensing for CEC-Enabled Devices Setup ProcedureAuto Input/Auto Output Sensing Screens ReceiverControlling A/V Receiver Sound Volume With a Standard TV SetupWith NetCommand IR Control With NetCommand for Hdmi CEC-Enabled Hdmi A/V ReceiverSource device connected directly to the TV Connecting a Computer to the TV Computer Video Connection Audio Video OutputUsing the TV with a Personal Computer Computer Video AdjustmentsImage Resolution Computer Display FormatsUsing a CableCARD Installing a CableCARDSeries TVs CableCARD MenuInstalling the Cable Tie Before You BeginCable Management Cable RoutingCable service or Hdmi and Audio SignalsIncoming from Satellite dishAudio Connect audioCables to Input Antenna with a Single Lead Wall Outlet Cable no cable boxAntennas with Separate UHF and VHF Leads VCR VCR to an Antenna or Wall Outlet CableVCR to a Cable Box Audio & Video Older Cable Box 26 3. TV ConnectionsReceiver Sound System Using the TV’s Audio Output Camcorder Audio-Only DevicePb Pr Component Video Connection Composite Video ConnectionTV Tips Sleep TimerChoosing a Viewing Source 23. F1-F4 For devices under NetCommand control Remote ControlCancel ChannelView Channel Listings Signal Strength Status DisplayAnt 1 TV-PG FAV1Fav Favorite Channels ANT-1TV Signals and Display Formats Signal DefinitionsDVD Image Definitions TV Display Format DefinitionsJpeg Thumbnail Menu Viewing Camera FilesJpeg Images and the USB Photo Port Media Setup Menu Camera Photos and Moving Video as Composite VideoSlide Show Keys for Jpeg Picture Slide ShowRemote Control Keys for the TV Menu System Main MenuAV Menu AV Menu OptionsFilm Mode Auto, Off Video Mute On, OffGlobal Audio Only On, OffVideo Menu Video Menu OptionsVert Adjustment SharpEdge On, OffDeepField ImagerAudio Menu Options Audio MenuFrom the Audio menu Captions Menu Captions on Analog ChannelsCaptions on Digital Channels Captions Menu Options1 Enter Setup MenuSetup Menu Options Setup menu, Edit channel options EditClock TimeManual DateTimer Setup menu, Timer optionsEnergy Fast Power On Mode Low Power Use the External Controller Input Wired IR option seeThis page intentionally left blank Only when Inputs NetCommand Inputs MenuInput Selection menu Selection menuLock Menu Pass CodesParent Menu Other Menu Alternate Rating SystemParent Menu Options U.S.-based rating system TV-YTV-Y7 TV-GOther Menu Options alternate rating system TimeAbout NetCommand IR Control Important Note on NetCommandIR Emitter Placement An IR emitter cable is included with the TVInitial NetCommand Setup for Most Devices If the device has no Power OFF key, skip this stepCH/PAGE PowerGuide Operating NetCommand-Controlled Devices Controlling Most Device TypesControlling an A/V Receiver Special Operation MethodsInside the Guide Outside the GuideSetting Up NetCommand Control of an A/V Receiver Receiver Control Power and VolumeSetup to Control A/V Receiver Power and Volume Before You BeginReceiver Control Automatic Audio Switching Audio Switching SetupAudio Available from TV only Analog Stereo AudioAV Receiver menu to set up audio switching More About Using an Hdmi Connection with this Setup VCRSetup to Control Switching to the TV’s Audio Output AVR menu for audio and video switching with Hdmi outputNetCommand IR Control Device Connected to an A/V Receiver Ated Assign Input column Assign Input1 throughAssign Input5 Open the Inputs Learn menuAppendix a Specifications Width Depth Weight lbsAppendix B Bypassing the Parental Lock Bypassing the Parental LockThis page intentionally left blank Appendix C Programming the Remote Control Functions Available for Other A/V DevicesProgramming the Remote Control DVDCABLE/SAT VCR DVD Audio Code VerificationProgramming Codes Make CodeCable Boxes Cable Boxes Make CodeSatellite Receivers Make Code Laser Disc PlayersReceivers Make Code VCRs Make Code ABSDVD Players DVD Players Make CodeAppendices75 Initial Guide Setup Appendix D TV Guide Daily 246 Series TVsMain Guide Screen Elements High-definition ChannelIcon NumberNavigating the Guide Setting Up TV Guide DailyUsing the TV Guide Daily System Modifying the Guide Setup Looking at AdsCustomizing Guide Listings Available OptionsProcedure TV Guide Daily Troubleshooting Tips Symptom RemarksConnecting Hdmi Devices to the TV Appendix E NetCommand Hdmi Control of CEC DevicesEnabling or Disabling the TV’s NetCommand Hdmi Control Appendices81 CEC-enabled A/V receiver functions that may be available Using NetCommand Hdmi ControlResetting Hdmi Control or Removing an Hdmi Device Figure Reset Name When to Use How to Use Resulting Action Appendix F TroubleshootingTV Reset Comparison Guide Service and Customer Support ServiceRead the ON-SCREEN TionsGeneral TV Operation Symptom Remarks TV Channels Symptom RemarksTV Power On/Off Symptom Remarks Picture Symptom RemarksSymptom Remarks Indicators Symptom Remarks NetCommand IR Control Symptom RemarksAppendices89 Trademark and License Information Mitsubishi TV Software To Obtain Warranty Service This Limited Warranty does not CoverWarranty93 Index Index95 MDEAservice@mdea.com System Reset