Speaker setting, Speaker Channel setting | JVC XV-FA90BK, XV-FA92SL

Initial settings

Speaker setting

Speaker Channel setting

2 Select the size using CURSOR 2/3.

• Large: Large speaker(s) which can fully reproduce

the low-frequency range.

Select the speaker configuration type according to your speaker system. Normally, simply select “5.1 CH.” or “2 CH.”. However, by selecting “EXPERT”, you can make fine tuning to match your speaker system.

PREFERENCE1		PREFERENCE2	SPK.SETTING
			5.1 CH.
			LEVEL
			DELAY
			F. SP	Large
			C. SP	Small
			R. SP	Small
			BASS	S.woofer
PRESS	KEY		TEST TONE

•	Small: Small speaker(s) which can not fully
	reproduce the low-frequency range.
•	None: No speaker(s) connected.

If you set the front speakers to “Small”, you cannot set the other speakers to “Large”.

Bass redirect

(available only when selecting EXPERT)

•2 CH.

When you connect to a 2-channel amplifier or TV.

•5.1 CH.

When you connect to a 5.1-channel amplifier and use the front, rear, center and sub-woofer speakers.

When you use small
speakers which do not fully	PREFERENCE1		PREFERENCE2	SPK.SETTING
reproduce the low-				LEVEL
				EXPERT
frequency range, you can				F. SP	Large
				DELAY
boost up the low-frequency		BASS		R. SP	Small
				C. SP	Small
signal of the sub-woofer or				BASS	S.woofer
front speakers.	PRESS	KEY		TEST TONE
front speakers.

Initial settings

•EXPERT

When you want to make fine tuning to match your speakers. The following five setting items are available.

NOTES

•When selecting “5.1 CH.” or “EXPERT”, set “DOWN MIX” to “OFF” (see page 60).

•The Dolby Digital LFE (Low Frequency Effect) signal is always fed from the SUBWOOFER output on the rear panel of the unit regardless of speaker setting.

•If you connect the unit's digital output to an external Dolby Digital or DTS decoder (and set the “DIGITAL AUDIO OUTPUT” option to “STREAM/PCM”), the speaker setting above is not effective. Make the speaker setting of the external decoder properly.

Speaker size settings

(available only when selecting EXPERT)

Sets the speaker sizes
according to your	PREFERENCE1		PREFERENCE2	SPK.SETTING
speakers.				EXPERT
speakers.				LEVEL
				DELAY
		BASS		F. SP	Large
		BASS		C. SP	Small
				R. SP	Small
				BASS	S.woofer
	PRESS	KEY		TEST TONE

1 Select the speaker to be set using CURSOR

5/∞.

•F.SP : Front speakers

•C.SP : Center speaker

•R.SP : Rear speakers

1 Select [BASS] using CURSOR 5/∞.

2 Select [S.woofer] or [L/R] using CURSOR

2/3.

•S.woofer: The low-frequency signal fed from the sub-woofer output is boosted up.

•L/R: The low-frequency signals fed from the front speaker outputs are boosted up.

The “Bass redirect” setting is effective only when at least any one of the speaker sizes is set to “Small”. If none of them is set to “Small”, this setting is not activated (“None” appears in the setting field).

Please note that the “L/R” setting is effective only when playing back a Dolby Digital encoded DVD VIDEO disc. If the front speaker size is set to “Small”, the Bass redirect setting is fixed to “S.woofer”.

Speaker level

(available only when selecting EXPERT)

You can adjust the output
level of each speaker.	PREFERENCE1		PREFERENCE2	SPK.SETTING
				EXPERT
				LEVEL
				DELAY
		BASS		F. SP	0dB
		BASS		C. SP	0dB
				R. SP	0dB
				S.WOOFER	0dB
	PRESS	KEY		TEST TONE

1 Select [LEVEL] using CURSOR 5/∞, then press ENTER.

The color of “LEVEL” changes.