Sim2 Multimedia HT300 XTRA-H installation manual Memories, Image, Picture

Page 25
MEMORIES

MEMORIES

The main parameters of the image may be saved in distinct groups of values (known as ‘Memories’); these parameters can subsequently be applied all together by way of a single com- mand.

There are 3 distinct Memories (Memory 1, Memory 2, Memory

3) for each of the 8 signal types managed:

 

 

1

VIDEO

 

 

 

2

S-VIDEO

3

COMP/RGB(YCrCb 15KHz)

3 COMP/RGB(RGB 15KHz)

3

COMP/RGB(YCrCb)

 

 

3 COMP/RGB(RGB)

 

4

GRAPHICS RGB

 

5

HDMI

 

making a total of 24 different available Memories.

The image parameters that can be saved/recalled by the Memo- ries management system are the following:

Image

Picture

BRIGHTNESS

ASPECT

CONTRAST

COLOR TEMP. GAIN (R/G/B)

COLOR

COLOR TEMP. GAIN OFFSET (R/G/B)

TINT

COLOR TEMP.

SHARPNESS

OVERSCAN

FILTER

GAMMA

SHARPNESS MODE

 

VIDEO TYPE

 

NOISE REDUCTION

 

Some of these parameters may not be available for certain in- puts or certain input signals, as indicated in Tables 1 and 2. The menu page for the Memories management functions is

activated by pressing the Image key on the remote control or the

￿key on the keypad (Fig.36).

20

 

 

 

05

 

 

GR

 

ZOOM

4

 

 

 

F1

2

 

O

 

 

1

 

CONTR

Fig.36

The operations that can be performed on each memory se- lected are described here below.

SAVE A MEMORY

To save the current values of the image parameters in Memory 1, use the ￿ and ￿ keys to move to line ‘1’ and then open the pull-down menu by pressing the ￿ key (Fig.37). Then select the option ‘Save current settings’. To confirm that the operation has been completed successfully, the message ‘Current set- tings saved in Memory 1’ is displayed at the bottom of the screen and the letter ‘S’ appears to the left of the memory name. The same procedure is used to save parameters in Memories 2 and 3.

Memories

0

Auto

 

1

S

Save current settings

 

 

2

I

Save initial settings

3

S

MEMORIARename 1

 

 

Fig.37

RECALL A MEMORY

To recall a Memory, select the desired line and press ￿. The parameters saved in the selected Memory will be applied to the image displayed and a message will appear to confirm the operation ‘Memory 1 recalled’. The Memory recalled will be associated with the source and signal type, and will be auto- matically recalled every time that particular source and signal type combination is selected.

SAVE DEFAULT SETTINGS

To restore the original values to a previously modified Memory, select the line corresponding to the Memory in question and open the pull-down menu ( ￿ key). Then select the line “Save default settings”. To confirm that the operation has been com- pleted successfully, the message ‘Initial settings saved in Memory 1’ is displayed at the bottom of the screen and the letter ‘I’ appears to the left of the name of the memory.

RENAME A MEMORY

It is possible to assign a name to each Memory. To assign a name (with a maximum length of 12 alphanumeric characters) to a Memory, select the option ‘Rename’ from the correspond- ing pull-down menu. Enter the text following the procedure in- dicated in paragraph “SOURCE LIST”.

23

Image 25
Contents HT 300XTRA-H HT User and Installation Manual The home theater projectorBACK LIGHT 1 INTRODUCTION SIM2 carries out comprehensive functional testing in order to guarantee the maximum product quality. For this reason, when you start using the product lamp operating hours may already be at between 30 and 1 Projection lens 2 Lens shift knob 3 Cooling air inlet vents Refer to trained, authorised personnel for technical assistance 2 IMPORTANT SAFETY INSTRUCTIONSDo not use the projector when the room temperature is above 35C 95F 3 PACKAGING AND CONTENTS ZOOM FOCUS 4 INSTALLATIONFor rear projection the screen must be translucent SWITCH ON FROM STAND-BY 5 SWITCHING ON AND OFF THE PROJECTORSWITCHING OFF AND RETURNING TO STAND-BY 6 CONNECTIONSLED INDICATORS S-VIDEO INPUT COMPOSITE VIDEO INPUTVGA INPUT RGB/YCRCB INPUTHDMI Fig. 21bMOTORISED PROJECTION SCREEN OUTPUT RS232 INTERFACE CONNECTOR 7 KEYBOARD PADUp/Down/Left/Right arrow keys Menufour 8 REMOTE CONTROLbatteries SOURCE SELECTION 9 ON SCREEN MENUFig. 26a MAIN MENUFig. 28a PICTUREFig. 28b BRIGHTNESSCINEMA MODE TABLE 1INPUT SIGNALS AND ADJUSTABLE/SETTING ITEMSVIDEO TYPE NOISE REDUCTIONASPECT IMAGECOLOR TEMPERATURE GAMMA CORRECTIONTABLE 2 INPUT SIGNALS AND ADJUSTABLE/SETTING ITEMS FREQUENCY/PHASEY / C DELAY ORIENTATION SETUPHORIZONTAL/VERTICAL KEYSTONE LENSFACTORY DEFAULTS POWER ONTEST PATTERNS MENU LANGUAGEF1/F2 KEYS MEMORIES Fig.36Image PictureNo Signal 10 CLEANING AND MAINTENANCECleaning the projector’s cover Cleaning the lensNo power Green and red LED are OFF 11 TROUBLESHOOTING GUIDEthe Image Adjustments menu The lamp is not coming on12 OPTIONAL ACCESSORIES OPTICAL HT A TECHNICAL SPECIFICATIONSOPTICAL HT 300 XTRA-H GENERAL ELECTRICALENVIROMENTAL CVBS on RCA/Phono type connectorC PROJECTION DISTANCES B DIMENSIONSFig.37a unit mm inches16/9 16/9 Image D ON SCREEN MENU LAYOUT PictureYCrCb Video S-VideoMenu SetupVIDEO S-VIDEOSave current settings Save initial settings Rename Memories0 Auto 1 S MEMORY 2 S MEMORY 3 S MEMORYINDEX Phone +39.434.383.253-256 Fax +39.434.383260-261