Sim2 Multimedia HT300 XTRA-H Cleaning And Maintenance, Info, Quick Menus, Messages, No Signal

Page 26
INFO

RESTORE CURRENT SETTINGS

On entering the ‘Memories’ menu, a copy of the current set- tings is saved in a temporary menu (labelled with 0 - AUTO). Once one or more memories have been recalled, you can re- store the settings that were effective at the moment the Memo- ries menu was accessed by selecting 0 - AUTO. However, this operation must be completed before the ‘Memories’ menu page disappears (30 seconds after the last operation commanded from the remote control or the keypad). The next time it ap- pears, the temporary memory will contain new information that takes into account any Memories selected the penultimate time the ‘Memories’ page was accessed.

Memory 0 (- AUTO) can be used even when you do not wish to enable the Memories management function for the signal currently in use. Once Memory 0 has been selected, when a source is chosen, the settings that were effective at the time the Memory was previously recalled will be automatically applied.

INFO

Displays the current status of the projector and information concerning the projected video/graphic signal.

This function is displayed on pressing QUICK MENUS on the remote control (or, in the absence of the On Screen Display, the ￿ key on the remote control).

QUICK MENUS

The Quick menus allows the adjustment of most of the picture quality controls without recalling the main On Screen menus. Brightness, Contrast, Color, Tint, Sharpness and Filter adjustments appear at the bottom of the screen, one after another, when Up and Down Arrow keys are pressed.

MESSAGES

The following messages could appear on your screen:

No Signal

The projector does not recognise any signal sent through the selected input.

-Check that the selected input is actually connected to a video or graphic signal.

-Verify compatibility of video/graphic signals with technical specifications of your projector.

-Check the integrity of cables used to connect various sources.

Out of range

Either the resolution or the horizontal/vertical frequency of the input signal is too high.

- Input a signal that is within specifications.

10 CLEANING AND MAINTENANCE

The projector does not require internal cleaning. There are no user serviceable parts inside the projector. Please refer all service requirements to qualified personnel.

Cleaning the projector’s cover:

Use a soft slightly damp cloth. Do not use abrasive cleaners, solvents or other harsh chemicals, as this will damage the finish of the cover. Avoid direct cleaning of the rear panel’s screen-

printing.

Cleaning the lens:

The lens may be cleaned with a very soft, non-abrasive small brush, in order to remove dust particles. Alternatively, use a soft dry cleaning cloth (of the type used for camera lens cleaning) to remove fingerprints and grease marks.

24

Image 26
Contents User and Installation Manual The home theater projector HT 300XTRA-H HTBACK LIGHT 1 INTRODUCTION SIM2 carries out comprehensive functional testing in order to guarantee the maximum product quality. For this reason, when you start using the product lamp operating hours may already be at between 30 and 1 Projection lens 2 Lens shift knob 3 Cooling air inlet vents 2 IMPORTANT SAFETY INSTRUCTIONS Refer to trained, authorised personnel for technical assistanceDo not use the projector when the room temperature is above 35C 95F 3 PACKAGING AND CONTENTS 4 INSTALLATION ZOOM FOCUSFor rear projection the screen must be translucent 5 SWITCHING ON AND OFF THE PROJECTOR SWITCH ON FROM STAND-BYLED INDICATORS 6 CONNECTIONSSWITCHING OFF AND RETURNING TO STAND-BY VGA INPUT COMPOSITE VIDEO INPUTS-VIDEO INPUT RGB/YCRCB INPUTMOTORISED PROJECTION SCREEN OUTPUT Fig. 21bHDMI Up/Down/Left/Right arrow keys 7 KEYBOARD PADRS232 INTERFACE CONNECTOR Menubatteries 8 REMOTE CONTROLfour Fig. 26a 9 ON SCREEN MENUSOURCE SELECTION MAIN MENUFig. 28b PICTUREFig. 28a BRIGHTNESSVIDEO TYPE TABLE 1INPUT SIGNALS AND ADJUSTABLE/SETTING ITEMSCINEMA MODE NOISE REDUCTIONCOLOR TEMPERATURE IMAGEASPECT GAMMA CORRECTIONY / C DELAY FREQUENCY/PHASETABLE 2 INPUT SIGNALS AND ADJUSTABLE/SETTING ITEMS HORIZONTAL/VERTICAL KEYSTONE SETUPORIENTATION LENSTEST PATTERNS POWER ONFACTORY DEFAULTS MENU LANGUAGEF1/F2 KEYS Image Fig.36MEMORIES PictureCleaning the projector’s cover 10 CLEANING AND MAINTENANCENo Signal Cleaning the lensthe Image Adjustments menu 11 TROUBLESHOOTING GUIDENo power Green and red LED are OFF The lamp is not coming on12 OPTIONAL ACCESSORIES OPTICAL HT 300 XTRA-H A TECHNICAL SPECIFICATIONSOPTICAL HT ENVIROMENTAL ELECTRICALGENERAL CVBS on RCA/Phono type connectorFig.37a B DIMENSIONSC PROJECTION DISTANCES unit mm inches16/9 16/9 YCrCb D ON SCREEN MENU LAYOUT PictureImage Video S-VideoVIDEO SetupMenu S-VIDEO0 Auto MemoriesSave current settings Save initial settings Rename 1 S MEMORY 2 S MEMORY 3 S MEMORYINDEX Phone +39.434.383.253-256 Fax +39.434.383260-261