JVC DT-V24L1D Menu Configuration-SET-UP Menu, Function Setting, Picture SUB ADJ, Size/Posi. Adj

Menu Configuration—SET-UP MENU

For the operation procedure, see page 7.

Operation guide

Shows the buttons for each operation.

NOTE

• The menu automatically disappears in about 30 seconds after the last menu operation.

• Some items may not appear on the menu depending on the input or the input signal. These items are not available.

12

FUNCTION SETTING

Setting for the tally lamp

Item	To do	Setting value
TALLY SELECT	Select the color of the tally lamp on the upper front panel.	GREEN, RED
TALLY BLINK	Select the blinking time of the tally lamp till it gets lighting.	OFF, 5sec., 8sec.

NOTE

The tally lamp is controlled using MAKE/TRIG. terminal of REMOTE terminals (☞ “External Control” on page 14).

PICTURE SUB ADJ.

Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.

Item	To do	Setting value
CONTRAST*1	Adjust the standard level for the contrast adjusted with	–20 – 00 – +20
	CONTRAST knob on the front panel.
BRIGHT*1	Adjust the standard level for the brightness adjusted with	–20 – 00 – +20
	BRIGHT knob on the front panel.
CHROMA*1	Adjust the standard level for the chroma adjusted with	–20 – 00 – +20
	CHROMA knob on the front panel.
PHASE*1	Adjust the standard level for the phase adjusted with	–20 – 00 – +20
	PHASE knob on the front panel.
NTSC SETUP*1	Select the set-up level of the input NTSC signal.	00 (compliant with 0% set-up signal), 7.5
		(compliant with 7.5% set-up signal)
COMPO. LEVEL	Select the level of the analog component signal.	SMPTE (compliant with M2VTR signals),
		B75 (compliant with BetacamVTR 7.5%
		set-up signal), B00 (compliant with
		BetacamVTR 0% set-up signal)
sub menu	Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing
	the actual picture.
reset	Restore the default settings for all the items in “PICTURE SUB ADJ.”

SIZE/POSI. ADJ.

Adjusts the size and position of the picture.

Item	To do	Setting value
H SIZE*2	Adjust the horizontal picture size.
H POSITION*2	Adjust the horizontal picture position.	Varies depending on the other
V SIZE*2	Adjust the vertical picture size.	settings.
V POSITION*2	Adjust the vertical picture position.
sub menu	Display the sub menu which enables you to adjust the items of “SIZE/POSI. ADJ.” while viewing
	the actual picture.
reset	Restore the default settings for all the items in “SIZE/POSI. ADJ.”

WHITE BALANCE SET.

Selects the color temperature and adjusts the drive level and cutoff point of each color (R/G/B).

Item	To do	Setting value
COLOR TEMP.	Select the color temperature.	HIGH(9300), LOW(6500), OTHER
R DRIVE, G DRIVE,	Adjust the drive level of each color (red, green, and blue).	MIN – 000 – MAX (in 256 grades)
B DRIVE*3
R CUT OFF, G CUT	Adjust the cutoff point of each color (red, green, and blue).	MIN – 000 – MAX (in 256 grades)
OFF, B CUT OFF*3
sub menu	Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while
	viewing the actual picture.
reset	Restore the default settings for the drive levels and cutoff points of the selected color
	temperature.

*1 Memorized for each input.

*2 Memorized for each signal format.

*3 Memorized for each color temperature (HIGH, LOW, OTHER).