JVC DT-V20L1 Available signals, Video signals, Computer signals preset DVI-D Hdcp terminals

Page 9

7Available signals

The following signals are available for this monitor.

Video signals

 

 

 

Input terminal

 

No.

Signal name

VIDEO

COMPO./RGB

HD/SD SDI (IN 1, IN 2)*1

DVI-D (HDCP)

(Analog component/

(DT-V24L1D and

(Digital component/digital

 

 

(INPUT1, INPUT2)

 

 

analog RGB)

DT-V20L1D only)

RGB)

 

 

 

1

NTSC

2

PAL

3

SECAM

4

BW(50Hz/60Hz)

5

480/60i

6

576/50i

7

480/60p

8

576/50p

9

640480/60p

10

720/60p

11

720/50p

12

720/30p

13

720/25p

14

720/24p

15

1080/60i

16

1035/60i

*2

17

1080/50i

18

1080/60p

19

1080/50p

20

1080/30p

21

1080/25p

22

1080/24p

23

1080/30psF

*3

*3

24

1080/24psF

: Acceptable

: Not acceptable

*1 Compatible with EMBEDDED AUDIO

*2 Displays the picture as 1080/60i, and “1080/60i” is displayed in the status display (page 7). *3 “1080/60i” is displayed in the status display (page 7).

Computer signals (preset)

DVI-D (HDCP) terminals

No.

Signal name

Screen resolution

Horizontal

Vertical

Scan system

Horizontal

Vertical

frequency (kHz)

frequency (Hz)

 

 

 

 

 

 

 

 

 

 

1

VGA60

640

480

31.5

59.9

Non-interlace

2

WVGA60

852

480

31.5

59.9

Non-interlace

3

SVGA60

800

600

37.9

60.3

Non-interlace

4

XGA60

1024

768

48.4

60.0

Non-interlace

5

WXGA (1280)

1280

768

47.8

60.0

Non-interlace

6

SXGA60

1280

1024

64.0

60.0

Non-interlace

7

SXGA+60

1400

1050

64.0

60.0

Non-interlace

8

SXGA+60*

1400

1050

65.2

60.0

Non-interlace

9

WSXGA+60

1680

1050

65.2

60.0

Non-interlace

10

UXGA60*4

1600

1200

75.0

60.0

Non-interlace

11

WUXGA60*4

1920

1200

74.0

59.9

Non-interlace

*4 For DT-V20L1D and DT-V20L1: When No. 10 or 11 signal is input, thin lines will become obscured because their signal resolution is higher than the screen resolution.

Specification of DVI-D (HDCP) terminal

Connect it to DVI-D output terminal on a personal computer.

Pin

Input signal

 

Pin

Input signal

 

Pin

Input signal

No.

 

No.

 

No.

 

 

 

 

 

1

T.M.D.S Data 2–

 

9

T.M.D.S Data 1–

 

17

T.M.D.S Data 0–

2

T.M.D.S Data 2+

 

10

T.M.D.S Data 1+

 

18

T.M.D.S Data 0+

3

T.M.D.S Data 2 shield

11

T.M.D.S Data 1 shield

19

T.M.D.S Data 0 shield

 

 

 

 

 

 

 

 

4

NC

12

NC

20

NC

 

 

 

 

 

 

 

 

5

NC

13

NC

21

NC

 

 

 

 

 

 

 

 

6

DDC Clock

14

+5 V Power

22

T.M.D.S Clock shield

 

 

 

 

 

 

 

 

7

DDC Data

15

GND

23

T.M.D.S Clock+

 

 

 

 

 

 

 

 

8

NC

 

16

Hot Plug Detect

 

24

T.M.D.S Clock–

Note for analog component/analog RGB signals

The monitor is compatible with G on sync, Y on sync and composite sync (Cs) signals. The monitor is not compatible with separate sync (HS/VS) signals.

Note for computer signals

Non-preset signals may not be displayed normally even if its frequency is within the acceptable range.

When a preset signal is input, the signal format is displayed on the screen. For other signals, the resolution is displayed.

Note for connections

Before making any connections, turn off all the equipment.

Use a cord whose plugs correctly match the terminals on this monitor and the equipment.

Plugs should be firmly inserted; poor connections could cause noise.

When unplugging a cord, be sure to grasp its plug and pull it out.

DO NOT connect the power cord until all connections are completed.

Refer also to the user manual of each piece of equipment.

9

Image 9
Contents DT-V24L1D DT-V24L1 DT-V20L1D DT-V20L1 Safety Precautions How to replace the fuseA. only Maintenance Installation Using the monitor on the standTo detach the stand To prevent an accidental fall To adjust the stand heightHigher position Lower position Use a JVC’s Rack Mount Adapter RK-C20L1 not suppliedDaily Operations / Connections Press buttons to select an item, then press button Display the menuPress Menu button to finish the audio channel selection Menu OperationsRear panel Attaching the Power Cord HolderVideo signals Available signalsComputer signals preset DVI-D Hdcp terminals Specification of DVI-D Hdcp terminalTechnical information Menu Configuration-MAIN MenuPicture Improvement Area MARKER*2Picture Function Audio SettingSync Function Operation guide Shows the buttons for each operationFunction Setting Menu Configuration-SET-UP MenuPicture SUB ADJ SIZE/POSI. ADJAll reset Control Lock Setting value OFF, onSetting for the information display of the monitor InformationUsing the MAKE/TRIGGER system External ControlAbout the external control Using the serial communication Self-check program TroubleshootingGeneral SpecificationsInput/output terminals Options not suppliedDT-V20L1D/DT-V20L1 DT-V24L1D/DT-V24L1Page Victor Company of Japan, Limited
Related manuals
Manual 20 pages 31.01 Kb