JVC LT-47X788, LT-42X788, LT-42XM48, LT-37XM48 manual Set Lock Code, Channel Guard Message

Page 36

Initial Setup

Set Lock Code

Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes pre- set with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below.

Press the MENU button

 

Initial Setup > Set Lock Code

 

 

π†

To "Initial Setup"

è

To enter

π†

To "Set Lock Code"

è

To operate (Password input screen will appear)

 

Enter the password by using the 10 keypad

Lock Code

0

 

1

 

2

 

3

 

 

 

 

 

 

Set

 

 

 

 

Clear

The Set Lock Code screen will appear

OK

BACK

 

MENU

 

Select

Operate

Back

Exit

 

To set the password, use the 10 keypad

Press the OK button to finish (your lock code is now set)

When a viewer attempts to watch a blocked channel, this message appears:

The channel will remain blocked until the correct lock code is entered (see above for information on setting your lock code).

Notes:

• After a power interruption you must reset the lock code.

This programming exceeds

your rating limits. Please enter lock code

by 10 key pad to unlock it.

No. - - - -

• Write your lock code number down and keep it hidden from potential viewers.

Channel Guard Message

When a viewer attempts to watch a guarded channel, the following message appears:

To watch a channel that you have locked, enter the Lock Code using the 10 key pad.

If the wrong code is entered, the message "Invalid Lock Code !” will appear on the screen.

The channel cannot be accessed until the correct code is entered.

Notes:

This channel is locked by channel guard.

Please enter lock code by 10 key pad to unlock it.

No. - - - -

Once a channel has been unlocked, it will remain unlocked until the television is turned off.

See also “Set Lock Code”.

36

Image 36
Contents LCD Flat Television Users Guide Important NoteImportant Safety Precautions Risk of Electric Shock Do not OpenImportant Safety Instructions 200 mm 150 mm Avoiding Ghost Images Examples include, but are not limited to the followingFor example Caring for the Cabinet Caring for the ScreenTidying the cables Disconnecting the stand Table of Contents Quick Setup Unpacking your TVRear Panel Diagram Side Panel DiagramPower TV ModelsRemote Control RM-C1450Using Menu Buttons Basic OperationGetting Started Connecting your devices Video CableDiagram #1 VCRAudio OUT Diagram #2 Connecting to a Camcorder CamcorderConnecting to an External Amplifier TV Rear Panel SpeakerSpeaker AmplifierConnecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Audio OUT Digital OUTConnecting to an amplifier using your optical output OUT Language Interactive Plug-in MenuAuto Clock Set Manual Clock SetAuto Tuner Setup Now ProgrammingUsing the Guide Onscreen MenusOnscreen Menu System Tuner Setup Picture Adjust 1/3 Picture Adjust 2/3Left main menu will appear Following menu you selected will appearSound Adjust Photo ViewerInitial Setup Noise MutingLanguage Front Panel LockV-Chip main screen will appear when the password is correct ChipUS V-Chip Ratings Setting US V-Chip Ratings Directions to set US V-Chip RatingsV-Chip main screen will appear Movies Ratings Directions to set Movie Mpaa RatingsCanadian V-Chip Ratings Directions to set Canadian V-Chip RatingsUnrated Programs Directions to Block Unrated ProgramsSet Lock Code Channel Guard MessageAuto Setting Closed CaptionManual Setting Power Indicator Auto Shut OffSoftware Version Optical Out Quick Start-upTuner Setup Auto Tuner SetupChannel Summary Continue to follow these directions for all seven spacesYour characters are now set Your characters are now reset Tuner Diagnostic Service Use Only Find ChannelDigital Antenna Level External Input Hdmi SizeVideo-1 Audio Video Input Label Picture Adjust Picture SettingsAdjust the Picture Settings Color TemperatureColor Management Dynamic GammaSmart Picture Digital VNR Natural CinemaPosition Adjustment ResetSound Adjust Sound SettingsAdjust the Sound Settings Turn On VolumeVolume Limit Clock/Timers Set ClockOn/Off Timer How to start the Photo Viewer How to finish the Photo ViewerPhoto Viewer Multi Screen Thumbnail appearsAuto Demo Slide ShowInterval Time Auto DemoPower Button FunctionsNumber Buttons 10Key Pad TuneVolume + InputChannel + Return +/TVSound MutingVideo Status Sleep Timer DisplayAspect Aspect RatiosMenu BackBy pressing the Aspect button, you can change the size When receiving analog broadcast By every press of the M L/M TS button, you change the modeWhen receiving digital broadcast Favorite Register the favorite channelDelete the favorite channel GuideMode External device control buttonsHow to set the codes Remote ProgrammingRemote programming Search Code FunctionProgramming Codes ABS MEIMGA HI-QTMK STSNAD ESAJBL AMW ADCWeak Signal OSD InformationAudio / Data Only Channel Troubleshooting Problems CheckTroubleshooting Following are not malfunctionsSpecifications Specifications subject to change without noticeVHF/UHF ATSC/DIGITAL Cable FIXModel LT-42X788 LT-47X788 Page Page JVC Company of America JVC CANADA, INC