Runco Q-750I operation manual Connecting 12-Volt, Trigger Output to External, Theater Equipment

Page 48

Installation

Connecting 12-Volt ➤	If your Q-750i is equipped with a CineWide with AutoScope system, connect the
Trigger Output to External	AutoScope lens motor to a 12-volt trigger output on the projector; see Figure 3-15.
Theater Equipment	Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or

	screen masks) to the other trigger output.
	AutoScope Lens Motor

Power AC Input

Switch

3.5-mm mini plug

Retractable Screen or other 12-volt trigger-activated device

Sleeve = Ground

Tip = +12V

Figure 3-15. Connecting 12-Volt Trigger Outputs

32	Q-750i Series Installation/Operation Manual

Image 48

Contents 750i Series 750i 750i/CineWide 750i/CineWide with AutoScopePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures CIE 1931 Color Coordinate Diagram and Effect of PCE Hue Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Controls and Functions 750i at a Glance750i Rear Panel Off = Normal operationComponent 1/SCART RCA connectors Trigger 2 3.5-mm, mini phono jackRS-232 750i Remote Control Q-750i Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlQuick Setup Installation OverviewProcedure For Details, Refer to If installing a CineWide-equipped projector InstallInstallation Considerations Projector Installation OptionsInstallation Type Ambient LightThrow Ratios for the Q-750i Series PrimaryLens Screen Lens Only Anamorphic Minimum Maximum Ceiling Installation Floor InstallationVertical and Horizontal Position Vertical and Horizontal Lens ShiftHorizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide/AutoScope Lens Mount With Installing the Fixed CineWide Base PlateInstalling the AutoScope Lens MotorRemove Projector Front Feet Install Lens Motor Q750i with Ceiling Mount Adapters/Projector StandsAutoScope Lens Motor Installation Installing the Fixed CineWide Base PlateDo not use the mounting screws provided with the ceiling Mounting the Q-750i Connections to750i Connecting Source Components to the Q-750iHDMI/DVI Connections See Figure 11. RGB Connections DTV Set-Top Box or Other Component YPbPr Source 12. Component Video Connections13. Composite and S-Video Connections RS-232 Controller ConnectionConnecting 12-Volt Trigger Output to ExternalTheater Equipment AutoScope Lens MotorConnecting an External IR Connecting to AC PowerReceiver Turning on the Power Primary Lens Adjustments Zoom Out FocusVertical Lens Shift To shift Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Too Far Left Correct position Too Far Right Anamorphic Lens Top View Geometry Installation Using Picture-In-Picture PIP OperationSelecting An Input SourceAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus Q-750i Main Menu Aspect Ratio Settings 169Letterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu Advanced Q-750i Advanced MenuPCE Color Gamut setting refer to Color Gamut, below X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Hue Saturation Hue13. Q-750i System Menu 14. Input Enable Sub-Menu PBP1 PBP2 16. PIP Split-Screen Mode Operation Language 17. Q-750i Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionMaintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes IR CodeKeyname Remote ButtonRemote Button Description Keyname Operations Control Commands Function Description IR Code RS232 Remote Button Description KeynameSerial Commands Operation Commands ValuesPip.select = ? Red.off = ? + Key = ? Blue.only White.red.gain = ? + RS-232 Error Codes RS-232 Error CodesError Code LED Indication Description Serial Communications Specifications 750i SpecificationsQ-750i Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsOverall Dimensions Q-750i Overall Dimensions Q-750iOverall Dimensions Q-750i/CineWide with AutoScope Overall Dimensions Q-750i/CineWide with AutoScopeSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1018-00 Rev. a October