Runco Q-750I operation manual You must enter a passcode to access the Save ISF

Page 66

Operation

Memory: Select Memory from the Main menu, then press ENTER to recall image quality settings previously saved, or to save changed settings in any of four memory locations.

•Recall Memory: Select Recall Memory from the Memory menu to recall saved image quality settings. Unless you select Default (see below), this control affects all sources, not just the active source.

•Custom 1 and Custom 2 contain the factory default settings when the projector is initially turned on.

•When you recall the ISF Day or ISF Night memory settings, all settings associated with these stored values are grayed out. This prevents unintended adjustments from being made. To remove this restriction, choose Custom 1 or Custom 2.

ISF Day and ISF Night are grayed out unless these custom settings have already been saved.

•Choose Default to restore the factory-default settings for the active source only. The other sources are unaffected.

•Save Settings: Select Save Settings from the Memory menu to save any image-related settings you have changed to Custom 1 or Custom 2.

The following items are saved (for all sources, not just the active source):

•Brightness / Contrast

•Color / Tint

•Sharpness

•Noise Reduction

•Color Space

•Video Standard

•Gamma

•Color Temperature

•DLP Frame Rate

•Color Gamut (including PCE settings)

•SatCo

•ConstantContrast

•Adaptive Contrast

•RGB Adjust (all settings in sub-menu)

•Save ISF: Select Save ISF from the Memory menu to save any image-related settings you have changed to the ISF Day or ISF Night memory location.

You must enter a passcode to access the Save ISF

Note sub-menu.

The settings that are saved are the same as those saved with the Save Settings command (see above).

50

Q-750i Series Installation/Operation Manual

Page 65 Page 67
Image 66
Page 65 Page 67
Contents 750i Series 750i 750i/CineWide 750i/CineWide with AutoScopePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures CIE 1931 Color Coordinate Diagram and Effect of PCE Hue Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Controls and Functions 750i at a Glance750i Rear Panel Off = Normal operationComponent 1/SCART RCA connectors Trigger 2 3.5-mm, mini phono jackRS-232 750i Remote Control Q-750i Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxInstallation Remote ControlProcedure For Details, Refer to Quick SetupInstallation Overview If installing a CineWide-equipped projector InstallInstallation Type Installation ConsiderationsProjector Installation Options Ambient LightThrow Ratios for the Q-750i Series PrimaryLens Screen Lens Only Anamorphic Minimum Maximum Ceiling Installation Floor InstallationVertical and Horizontal Position Vertical and Horizontal Lens ShiftHorizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide/AutoScope Lens Mount With Installing the Fixed CineWide Base PlateInstalling the AutoScope Lens MotorRemove Projector Front Feet Install Lens Motor Q750i with Ceiling Mount Adapters/Projector StandsAutoScope Lens Motor Installation Installing the Fixed CineWide Base PlateDo not use the mounting screws provided with the ceiling Mounting the Q-750i Connections to750i Connecting Source Components to the Q-750iHDMI/DVI Connections See Figure 11. RGB Connections DTV Set-Top Box or Other Component YPbPr Source 12. Component Video Connections13. Composite and S-Video Connections RS-232 Controller ConnectionTheater Equipment Connecting 12-VoltTrigger Output to External AutoScope Lens MotorConnecting an External IR Connecting to AC PowerReceiver Turning on the Power Primary Lens Adjustments Zoom Out FocusVertical Lens Shift To shift Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Too Far Left Correct position Too Far Right Anamorphic Lens Top View Geometry Installation Selecting An Input Using Picture-In-Picture PIPOperation SourceAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus Q-750i Main Menu Aspect Ratio Settings 169Letterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu Advanced Q-750i Advanced MenuPCE Color Gamut setting refer to Color Gamut, below X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Hue Saturation Hue13. Q-750i System Menu 14. Input Enable Sub-Menu PBP1 PBP2 16. PIP Split-Screen Mode Operation Language 17. Q-750i Service Menu OSD menus are not available when in test pattern mode Operation Troubleshooting Chart Maintenance and TroubleshootingTroubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting Key Commands Serial CommunicationsKeyname Serial Command Key Names and IR CodesIR Code Remote ButtonRemote Button Description Keyname Operations Control Commands Function Description IR Code RS232 Remote Button Description KeynameSerial Commands Operation Commands ValuesPip.select = ? Red.off = ? + Key = ? Blue.only White.red.gain = ? + RS-232 Error Codes RS-232 Error CodesError Code LED Indication Description Serial Communications Specifications 750i SpecificationsQ-750i Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsOverall Dimensions Q-750i Overall Dimensions Q-750iOverall Dimensions Q-750i/CineWide with AutoScope Overall Dimensions Q-750i/CineWide with AutoScopeSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1018-00 Rev. a October

Q-750I specifications

The Runco Q-750I is a state-of-the-art home theater projector that has earned a reputation for delivering exceptional image quality and advanced features. Designed to cater to the needs of cinephiles and home theater enthusiasts alike, the Q-750I incorporates a range of technologies that elevate the viewing experience to new heights.

One of the standout characteristics of the Runco Q-750I is its use of cutting-edge DLP technology. The projector employs a BrilliantColor™ technology that enhances the color accuracy and brightness, delivering vivid and realistic images. With a native resolution of 1080p, it ensures that even the smallest details in high-definition content are rendered crisply and clearly.

In addition to its impressive resolution, the Q-750I also features an advanced optical system. The projector's lens system, which includes multiple lens elements, ensures minimal distortion and superior image sharpness across the entire screen. This attention to detail means that viewers can enjoy an immersive cinematic experience without compromising on image quality.

The Q-750I also stands out with its extensive installation flexibility. With a motorized lens shift feature, users can easily adjust the projector's position to fit various screen sizes and setups. This aspect, combined with a robust zoom capability, allows for seamless integration into any home theater design.

Another significant feature of the Runco Q-750I is its support for 3D content. With the increasing popularity of 3D films and gaming, the Q-750I can project stunning three-dimensional visuals, providing an engaging experience that makes viewers feel part of the action. It is compatible with the latest 3D formats, ensuring that users can enjoy their favorite content without any compromise.

Moreover, the projector is equipped with Runco's proprietary Vivix™ video processing technology. This advanced processing system enhances the quality of both standard and high-definition content, optimizing color, contrast, and motion handling. The result is a smoother and more lifelike viewing experience, particularly in dynamic scenes.

On the connectivity front, the Q-750I is well-equipped with multiple input options, including HDMI, Component, and RS-232 for integration with control systems. This ensures compatibility with a wide range of devices, making it a versatile choice for any home theater setup.

In summary, the Runco Q-750I is a feature-packed projector that combines high-end technologies with user-friendly design. Its impressive image quality, installation versatility, and support for 3D content make it an ideal choice for anyone looking to create a truly immersive home theater experience. As technology continues to evolve, the Q-750I stands out as a premium option for discerning viewers who demand the best in home entertainment.
Top Page Image Contents