Runco Q-750I operation manual Copyright and Trademarks

Page 6

Exclusion of Damages

RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT.

1.RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

2.RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR OTHERWISE.

3.RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.

Effect of Local Law

This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

COPYRIGHT AND TRADEMARKS:

© Copyright 2009 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of Runco.

The trademarks reporduced in this Runco Owner’s Manual and used on the Runco Products are either owned by Runco or are licensed by Runco. You may not reproduce or use the trademarks without the prior written consent of Runco.

Runco Products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents Pending.

vi

Q-750i Series Installation/Operation Manual

Image 6
Contents 750i Series 750i 750i/CineWide 750i/CineWide with AutoScopePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures CIE 1931 Color Coordinate Diagram and Effect of PCE Hue Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Controls and Functions 750i at a Glance750i Rear Panel Off = Normal operationComponent 1/SCART RCA connectors Trigger 2 3.5-mm, mini phono jackRS-232 750i Remote Control Q-750i Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxInstallation Remote ControlProcedure For Details, Refer to Quick SetupInstallation Overview If installing a CineWide-equipped projector InstallInstallation Type Installation ConsiderationsProjector Installation Options Ambient LightThrow Ratios for the Q-750i Series PrimaryLens Screen Lens Only Anamorphic Minimum Maximum Ceiling Installation Floor InstallationVertical and Horizontal Position Vertical and Horizontal Lens ShiftHorizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide/AutoScope Lens Mount With Installing the Fixed CineWide Base PlateInstalling the AutoScope Lens MotorRemove Projector Front Feet Install Lens Motor Q750i with Ceiling Mount Adapters/Projector StandsAutoScope Lens Motor Installation Installing the Fixed CineWide Base PlateDo not use the mounting screws provided with the ceiling Mounting the Q-750i Connections to750i Connecting Source Components to the Q-750iHDMI/DVI Connections See Figure 11. RGB Connections DTV Set-Top Box or Other Component YPbPr Source 12. Component Video Connections13. Composite and S-Video Connections RS-232 Controller ConnectionTheater Equipment Connecting 12-VoltTrigger Output to External AutoScope Lens MotorConnecting an External IR Connecting to AC PowerReceiver Turning on the Power Primary Lens Adjustments Zoom Out FocusVertical Lens Shift To shift Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Too Far Left Correct position Too Far Right Anamorphic Lens Top View Geometry Installation Selecting An Input Using Picture-In-Picture PIPOperation SourceAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus Q-750i Main Menu Aspect Ratio Settings 169Letterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu Advanced Q-750i Advanced MenuPCE Color Gamut setting refer to Color Gamut, below X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Hue Saturation Hue13. Q-750i System Menu 14. Input Enable Sub-Menu PBP1 PBP2 16. PIP Split-Screen Mode Operation Language 17. Q-750i Service Menu OSD menus are not available when in test pattern mode Operation Troubleshooting Chart Maintenance and TroubleshootingTroubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting Key Commands Serial CommunicationsKeyname Serial Command Key Names and IR CodesIR Code Remote ButtonRemote Button Description Keyname Operations Control Commands Function Description IR Code RS232 Remote Button Description KeynameSerial Commands Operation Commands ValuesPip.select = ? Red.off = ? + Key = ? Blue.only White.red.gain = ? + RS-232 Error Codes RS-232 Error CodesError Code LED Indication Description Serial Communications Specifications 750i SpecificationsQ-750i Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsOverall Dimensions Q-750i Overall Dimensions Q-750iOverall Dimensions Q-750i/CineWide with AutoScope Overall Dimensions Q-750i/CineWide with AutoScopeSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1018-00 Rev. a October