Runco operation manual 1. LS-7Specifications continued

Page 94

Table 7-1. LS-7 Specifications (continued)

Specifications

Table 7-1. LS-7 Specifications (continued)

	Performance

Microdisplay:	Texas Instruments DLP® 1280x720 DMD (x 3)

Native Resolution:	1280 x 720 (921,600 pixels)

Aspect Ratios:	Native (Pixel-to-Pixel), 16:9, Letterbox, 4:3, 4:3 Narrow,
	Letterbox (Anamorphic lens compatible)

Projection Lens:	F/3.5, 25.5~32.0mm focal length

Throw Ratios:	1.85 – 2.40 (distance/width) – Standard lens
	1.56 – 1.86 (distance/width) – Optional short-throw lens

Vertical Lens Shift Range:	65% of screen height above or below lens center
	(130% of one half of the screen height)

Horizontal Lens Shift Range:	30% of screen width left or right of lens center
	(60% of one half of the screen width)

Video Lumens:	2,000 ANSI lumens (average) calibrated at D65

Sequential Contrast –	20,000:1 typical
ConstantContrast On:

Cooling Performance:	High efficiency adaptive voltage side-to-side cooling
	with low system acoustic noise level and low light
	pollution cabinet

Projection Modes:	Front, Rear, Ceiling (front/rear)

Lamp:	User replaceable 230/260W HPM (selectable), 2500
	hour lifetime at 230W setting

Video Processing:	Runco advanced ViVix processing with 10 bit
	independent dual channel image processing, true 1080i
	deinterlacing, MPEG artifact reduction (block and
	mosquito noise), latest motion adaptive processing, 3D
	noise reduction, detail enhancement, rich color
	processing and noise reduction, less than one frame
	latency

Calibration:	Full RGB gain/offset control (White Balance), Gamma,
	Contrast, Color Temperature, Brightness

78	Runco LS-7 Installation/Operation Manual

Image 94

Contents LS-7 Home Theater ProjectorPage Warranty Coverage RuncoCare Standard Two Year Limited WarrantyRuncoCare Standard Features Length of WarrantyRuncoCare Claim Procedure Warranty ExclusionsOnline Product Registration Extended Service OptionsLimitation of Implied Warranties Effect of Local Law Exclusion of DamagesCOPYRIGHT AND TRADEMARKS Important Safety Instructions Compliance Information DECLARATION OF CONFORMITYPRODUCT DISPOSAL FCC PARTINDUSTRY CANADA ICES-003 IMPORTANT RECYCLE INSTRUCTIONSPage RuncoCare Standard Two Year Limited Warranty Table of Contentsviii Floor Mounting Upright Operations Commands Serial Command SyntaxKey Commands RS-232Error CodesTable of Contents List of Figures List of Figures Target Audience 1. Introduction1.1 About This Manual If You Have Comments1.2 Using This Manual DANGEROptional Accessories 1.3 Description, Features and BenefitsKey Features and Benefits Parts List Introduction SOURCE 2. Controls and Functions2.1 LS-7at a Glance MENUPROJECTION LENS EXHAUST VENTINTAKE VENT FRONT IR SENSOR1.RUNCO LOGO BADGE 2.REAR COVER 6.ADJUSTABLE FEETFigure 2-2. LS-7Rear/Bottom/Top View 3.LAMP MODULE COVERFigure 2-3. LS-7Rear Panel 5.COMPONENT 1/SCART RCA connectors2.2 LS-7Rear Panel 1.HDMI 1 Digital HDMI 2 Digital8.IR INPUT 2.3 LS-7Remote Control7.S-VIDEO 9.TRIGGER 2 3.5-mm,mini phono jackSharpness SHARP Press to adjust sharpness 7.Memory Preset Buttons M1 / M2 / M38.Picture Adjustment Buttons Contrast 5.Aspect Ratio Selection ButtonNotes on Remote Control 3. Installation3.1 Remote Control Notes on BatteriesInstallation Figure 3-1.IR Reception Angles90.0 Table 3-1.Installation Overview 3.2 Quick SetupInstallation Installation Type InstallationTable 3-2.Projector Installation Options ConsiderationsFigure 3-2.Estimating Throw Distance Ambient LightThrow Distance Estimating Throw DistanceTable 3-3.Throw Ratios for the LS-7Series Floor InstallationFigure 3-3.Projector Placement Vertical and HorizontalLens Shift Figure 3-4.Vertical Lens Shift Example OnlyFigure 3-5.Horizontal Lens Shift Example Only InstallationFolded Optics Adjusting the Projection3.4 Mounting the LS-7 Figure 3-6.Folded Optics3.5 Connections to the LS-7 HDMI/DVI Connections See Figure Connecting SourceComponents to the LS-7 Figure 3-7.HDMI/DVI Source ConnectionsFigure 3-8.RGB Connections Installation DTV Set-TopBox or Other Component YPbPr SourceFigure 3-9.Component Video Connections Y Pb Pr Y Pb PrInstallation Figure 3-10.Composite and S-VideoConnectionsDVD Player, VCR Satellite Receiver Laser Disc etc Connection to Automation/ Control System or PCRS-232Controller Figure 3-11. RS-232Control System ConnectionTrigger Output to External Connecting 12-VoltConnecting an External IR Theater EquipmentConnecting to AC Power 3.6 Turning on the Power 3.7 Lens AdjustmentsFocus Zoom Lens Shift Installation 3.8 Changing the OSD Languageshift exceeds 50 per cent of the screen height 3.9 Adjusting the Picture Orientation Rear Projection Ceiling ModeInstallation 4.2 Selecting an Aspect Ratio 4. Operation4.1 Selecting Video Memory 4.3 Selecting An Input Source4.4 Using Picture-In-PicturePIP separated by their display modes4.5 Using the On-ScreenMenus Advanced ServiceMain Figure 4-1. LS-7OSD Menu StructureMain Figure 4-2. LS-7Main MenuTable 4-2.Aspect Ratio Settings Table 4-2.Aspect Ratio Settings continued OperationOperation Table 4-2.Aspect Ratio Settings continuedAspect You must enter a passcode to access the Save ISF Note sub-menuBelow Black Above Black Operation Operation Figure 4-6.Overscan Examples Figure 4-7. Source Select Sub-Menu OperationAdvanced Figure 4-8. LS-7 Advanced MenuStandard for your region Table 4-3.x/y Color Gamut Values Figure 4-9. RGB Adjust Sub-Menu Offset settings reduce the image brightnessFigure 4-10. Fine Sync Sub-Menu OperationOperation System Figure 4-11. LS-7 System MenuFigure 4-12. Source Enable Sub-Menu PBP2 Figure 4-13.PIP and PBP areas for 720p DisplayPBP1 DMD AreaFigure 4-14.PIP Split-ScreenMode OperationControl Figure 4-15. LS-7 Control MenuTrigger 2 operates identically to Trigger Language OperationFigure 4-16. LS-7 Service Menu ENTER Lamp Hours User Memory 1 / User Memory ISF DayOperation 5. Maintenance and Troubleshooting 5.1 Lamp ReplacementTable 5-1.Troubleshooting Chart 5.2 Troubleshooting TipsMaintenance and Troubleshooting Table 5-1.Troubleshooting Chart continued Maintenance and TroubleshootingMaintenance and Troubleshooting Key Commands 6.1 RS-232Connection and Port ConfigurationSerial Command Syntax 6. Serial CommunicationsTable 6-1.Serial Command Key Names and IR Codes gam.crt Precede operation and command with a space op operation command CRThe command type can be one of 5 functions Table 6-2.Serial Commands Table 6-2.Serial Commands continued Table 6-2.Serial Commands continued source.selTable 6-2.Serial Commands continued ccontTable 6-2.Serial Commands continued blank.screenTable 6-2.Serial Commands continued act.sourceTable 6-2.Serial Commands continued statusLED Indication Table 6-3. RS-232Error CodesError Code DescriptionTable 7-1. LS-7Specifications 7. SpecificationsLS-7Specifications SpecificationsTable 7-1. LS-7Specifications continued SpecificationsSpecifications Table 7-1. LS-7Specifications continuedGeneral Specifications 7.2 LS-7DimensionsFigure 7-1. LS-7Dimensions 1007.3 Supported Timings Table 7-2.Supported Signal Timings by InputSpecifications PAL-M SpecificationsPAL-B/G PAL-60Page 020-1038-00Rev. A December