JVC LT-20A60SU Picture Mode, Sleep Timer, Mute Indicator, No-Signal Detection TV mode, Volume Bar

Page 22

In stereo transmission it yields a phase differ- ence between left and right channels. Hyper Sound selection will be displayed on the screen when the TV Status button is pressed or programme￿￿￿￿is changed. ￿￿￿￿￿

Picture Mode

Picture mode OSD is displayed when BLUE button is pressed. Picture mode can be changed to standard, soft, and bright.

Sleep Timer

Sleep Timer mode OSD is displayed when YELLOW button is pressed.

The Sleep Timer is used to turn the TV off after a defined period of time after selecting this item. The timer can be programmed between Off and 120 minutes in steps of 10 minutes. (OFF, 010, 020, 030, 040, ... , 120)

If sleep timer is activated, at the end of the selected the time, the TV goes automatically to stand-by mode.

Mute Indicator

It is placed in the upper middle of the screen when enabled, and it stays there until it is dis- abled.

To cancel mute, there are two alternatives; the

first one is by pressing the "" button, this volume is set to the preceding value, and the second one is increasing the volume level. By decreasing the volume level in mute state, mute will not be ignored, only the volume level will decrease.

No-Signal Detection (TV mode)

If no valid signal detected, it takes 5 minutes to switch to the Stand-By mode unless any signal detected or any Remote Control com- mand is accessed.

After a Remote Control command (if No-Sig- nal Timer is active) the timer stops and if no signal detected again the timer is initialized to 5 minutes and starts 3 seconds later again to count down.

It is not valid in EXT modes.

No-Signal and Out Of Range Detection (PC mode)

In PC Mode,as no menu is displayed,in case that there is no PC input to the TV,it is dis- played an OSD message:

No input signal detected

then the power lamp turns to amber and PC will be in PC standby mode. Press AV button,

digit buttons or “ ” / “ buttons to exit standby mode.

In PC Mode,as no menu is displayed,in case that there is no PC input to the TV, but the reso- lution and the vertical frequency is not sup- ported by the concept, it is displayed an OSD message:

Signal out of range

Volume Bar

It is displayed in the lower middle of the screen. When a volume command is received (press-

ing “ +” or “ -” by Remote Control or Control panel at the top of the TV) and no menu is active, it stays on the screen for 3 seconds, after the last volume command or until an- other command is received in between.

EXT Modes

By pressing the “AV” button you can switch your TV to EXT modes (except being in Tele- text). Pressing this button will consecutively switch the TV in one of the optional EXT modes: EXT-1, EXT-2, EXT-2 S, EXT-3, EXT-4, EXT-4 S and PC.

ENGLISH - 21 -

Image 22
Contents LT-20A60SU Contents For your safetyDO… English Important Information Please take note Care and disposalRemote Control Buttons Green227723&295 Control Panel ButtonsUsing the stand Remove the terminal Cover Where to install Before Switching on your TV PreparationInserting batteries in the remote control handset Switching the TV ON/OFFHow to connect other devices To switch the TV onOperating the TV First A.P.S. Automatic Programming SystemOperating with Remote Control MenuSystem Picture MenuEnglish Sound Menu Feature Menu Install Menu TonProgram Menu Source Menu Other FeaturesSound Indicator TV StatusMute Indicator Picture ModeSleep Timer No-Signal Detection TV modeZoom Modes AutoMain Menu in PC mode PC ModeInstallation PC Picture Position MenuPC Picture Menu Sound in PC modePIP Picture Teletext PeripheralEquipment ConnectionsVia the ANT aerial socket Connecting HeadphonesConnecting the PC DecoderPeripheralEquipmentConnections AntennaConnections PeripheralEquipmentConnections PC Input Typical Display Modes Tips Specifications LT-20A60SU