Wireless network setting
This menu is displayed only when you set Wireless in
Network selection. In order to use a wireless network, you must set up a connection to the AP (e.g. wireless router).
3Use ▲▼ to select Wireless network setting, then press OK.
Auto
Search for wireless networks automatically and select the SSID from the list.
4 Use ▲▼ to select Auto, then press OK.
5 The list of wireless networks will be displayed.
Use ▲▼ to select the appropriate the SSID, then press OK.
| Auto |
| Router 1 |
|
|
|
|
| Enter Key |
|
|
|
|
|
|
| |||
| Manually enter your S |
| Router 2 |
|
|
|
|
| Select |
|
|
|
|
|
|
| |||
|
|
| Router 3 |
|
|
|
|
| Enter Key |
|
|
|
|
|
|
|
| ||
|
|
| Router 4 |
|
|
|
|
| Select |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
•If you select the SSID with 
,WEP*2 / WPA / WPA2 Key entry screen will appear.
Enter the WEP*2 / WPA / WPA2 key of the selected wireless network using ▲▼◄►, then press OK.
•If you select the SSID has a WPS, the WPS setting screen will appear.
Use ▲▼◄► to select a setting, then press OK.
| Select this setting if your router has a WPS | |
| button. Start scanning for wireless networks on | |
Simple connect | the TV after pressing the WPS button on your | |
router. If connection test fails, try Simple connect | ||
| again.*1 | |
| If it fails then refer to the router’s manual for | |
| more details. | |
| Select this setting if your router has a WPS but | |
WPS code | does not have a WPS button. Enter the | |
WPS PIN code shown on your TV in the router | ||
| ||
| settings menu via PC before Connect is selected. | |
|
| |
| If your wireless network with authentication | |
| setting | |
Manual | WEP*2 / WPA / WPA2 Key entry screen will | |
appear. Enter the WEP*2 / WPA / WPA2 key of | ||
| the selected wireless network using ▲▼◄►, | |
| then press OK. |
*1 WPS (Simple connect) cannot be used when the security protocol is set to WEP. Change the Access Point’s security mode from WEP to WPA or WPA2 (recommended).
*2 WEP is not recommended to be used due to its Major security flaws. Change the Security protocol on the wireless router to WPA or WPA2 (recommended) mode.
Confirmation message will appear. Select OK to complete the settings.
Note
••For a wireless network with authentication setting, key icon appears to the right hand of the SSID.
••Signal icon shows the strength of the signal.
••WEP*2 / WPA key appears as asterisks on the confirmation screen.
••The wireless LAN supports following specifications.
: IEEE 802.11 b/g/n | |
: 2.4GHz | |
: WEP*2 / WPA / WPA2 |
32 English
Manually enter your SSID
Set up the connection to the AP (e.g. wireless router) manually by entering the SSID.
4Use ▲▼ to select Manually enter your SSID, then press OK.
•AP (e.g. wireless router) SSID entry screen will appear. Enter the SSID using ▲▼◄►, then press OK.
5Use ▲▼ to select the authentication setting of the selected wireless network.
•For a wireless network with authentication setting, select the authentication setting, according to the security type of the wireless network.
Select security type for | None |
"Router 1" |
|
| WEP |
| |
|
|
Back |
|
|
|
|
|
None | Set the authentication setting to None. |
WEP*2 | Set the authentication setting to WEP.*2 |
Set the authentication setting to | |
Set the authentication setting to |
•For a wireless network without authentication setting, select None.
•If you select WEP*2,
Enter the WEP*2 / WPA / WPA2 key of the selected wireless network using ▲▼◄►, then press OK.
•Confirmation message will appear. Select Yes to complete the settings.
*2 WEP is not recommended to be used due to its Major security flaws. Change the Security protocol on the wireless router to WPA or WPA2 (recommended) mode.
Continued on next page.