4
Important Safety Instructions
English
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments / accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
Note to the CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article
Example of Antenna Grounding as per NEC − National Electric Code
GROUND CLAMP | ANTENNA LEAD IN WIRE |
|
ANTENNA DISCHARGE
UNIT (NEC SECTION
GROUNDING CONDUCTORS
(NEC SECTION
GROUND CLAMPS
ELECTRIC SERVICE |
| POWER SERVICE GROUNDING |
| ELECTRODE SYSTEM | |
EQUIPMENT |
| |
| (NEC ART 250, PART H) | |
|
|
Wall Mount Bracket Kit
Brand: SANUS
| Model # | Screw dimension |
22MV402X | SAN10b | M4 x 0.472” (12mm) |
|
|
|
For 26 inch TVs, screws w/washers are required. (sold separately)
26MV402X |
| M4 x 0.472” (12mm) |
SAN213b | + | |
|
| Washer 0.039” (T1mm) |
|
| Do NOT use screws |
| packed withWall Mount Bracket Kit | |
| For 32 inch TVs, you need to purchase screws | |
| separately with dimensions described below. | |
32MV402X | VM200s | M4 x 0.472” (12mm) |
•The recommended Wall Mount Bracket Kit (sold separately) allows the mounting of the TV on the wall.
•For detailed information on installing the wall mount, refer to the Wall Mount Instruction Book.
•Funai is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV Wall Mount Bracket or mount the TV onto the Bracket on your own.
•The Wall Mount Bracket must be installed by experts.
Funai is not liable for these types of accidents or injury noted below.
•Install the Wall Mount Bracket on a sturdy vertical wall.
•If installed onto a ceiling or slanted wall, the TV and Wall Mount Bracket may fall which could result in a severe injury.
•Do not use screws that are longer or shorter than their specified length. If screws too long are used this may cause mechanical or electrical damage inside the TV set. If screws too short are used this may cause the TV set to fall.
•Do not fasten the screws by excessive force.This may damage the product or cause the product to fall, leading to an injury.
•For safety reasons use 2 people to mount the TV onto a Wall Mounting Bracket.
•Do not mount the TV onto the Wall Mounting Bracket while your TV is plugged in or Turned On. It may result in an electrical shock injury.
When installing the unit on the wall, allow this much space.
Top: | 11.8 inches | (30cm) |
Left and right side: | 5.9 inches | (15cm) |
Bottom: | 3.9 inches | (10cm) |