NCR NCR 5972 manual Radio Frequency Interference Statements, Federal Communications Commission FCC

Page 9

Chapter 1: Introduction

0-7

Radio Frequency Interference Statements

Federal Communications Commission (FCC)

Information to User

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

NCR is not responsible for any radio or television interference caused by unauthorized modification of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by NCR. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The user is cautioned that changes or modifications not expressly approved by NCR may void the user’s authority to operate the equipment.

Canadian Department of Communications

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectriques édicté par le ministrère des Communications du Canada.

Voluntary Control Council For Interference (VCCI)

Image 9
Contents Userʹs Guide Page Preface Safety RequirementsIntroduction Table of Contents Programming Set Up InstallationService Revision Record Federal Communications Commission FCC Radio Frequency Interference StatementsCanadian Department of Communications Voluntary Control Council For Interference VcciIntroduction Features ModelsVFD Models Software LCD Models Introduction Working Range Physical EnvironmentTransit Environment Storage EnvironmentVFD Models DimensionsInch Post 119 mm 356 mm 14.1 95 mm 3.75 LCD Models Operational Environment Electrical Environment2x20 Customer Display Parallel Cable VFD Mounting Hole Dimensions2x20 Customer Display Serial Cable LCD Site Preparation Selv Power Source Warning Installing the Customer DisplayCable Requirements Installation GoalInstallation Procedures Power Supply ChoicesRS-232 Serial Interface Diagnostics Micro-controller TestExternal Memory Test Character VFD Only Firmware Part Number Display Pixel TestHost/Retail Display Command Interface Programming Set UpRetail Display Commands Command Function Format 1B Returns xx yy zz Reset DisplaySet Diagnostic State On Erase DisplayFormat 1B Set Display State On Set Low Power State OnDisable Cursor Enable CursorSet Screen Save Blank Set Screen Save WalkFormat 1B 0A Disable Screen Save Option Enable Character BlinkTurn On Screen Save Move Cursor Left Disable Character BlinkMove Cursor Right Format 1B 0EMove Cursor Down Move Cursor UpFormat 1B 13 nn Move Cursor To Specified PositionRead Display ID Byte Brightness AdjustmentFormat 1B 17 nn Range 01 ≤ nn ≤ Format 1B Returns 0x8ARead Display ID String Display ESC CharacterSelect Character Set n Code Page 850 International Character Sets014 Programming Set Up 056 077 078 079 098 099 100 101 120 121 122 123 124 125 140 141 142 143 144 145 161 162 182 183 Programming Set Up 224 225 226 227 228 229 245 246 247 248 249 250 251 252 253 254 255 Code Page Katakana Programming Set Up Programming Set Up Programming Set Up 084 085 086 106 107 108 Programming Set Up Programming Set Up 168 169 170 190 191 192 193 210 Programming Set Up 254 Code Page 866 Cyrillic Programming Set Up Programming Set Up 072 073 074 075 076 077 084 085 086 106 107 108 128 147 148 149 150 171 172 173 174 Programming Set Up Programming Set Up 234 235 236 237 253 254 255 Programming Set Up Safety Requirements ServiceService Troubleshooting Procedures Servicing the DisplayNormal Operation Servicing the VFD or LCD Remove only two cabinet screws Remove power from the unit before cleaning Cleaning the Display