ViewSonic VS11856 user manual Connection ports Remote Control, Power, Menu, Color Temp

Page 7

Connection ports

Remote Control

(1)	(2)	(3)	(4)	(5)	(6)	(7)
						(1)
(8) (9)					(10)	(11)

1.	RS-232 terminal
	When operating the projector via a computer, connect this to the controlling computer’s RS-232C port.
2.	USB terminal (Service purpose)
	This connector is for firmware upgrade.
3.	HDMI-1 terminal	(2)
	Interface for digital video.
4.	HDMI-2 terminal
	Interface for digital video.	(3)
5.	RGB IN terminal	(4)
5.	RGB IN terminal
	Connects PC input signal (analog) to this jack.
6.	COMPONENT VIDEO 1 terminals	(5)
		(5)
	Analog/digital video interface transmits via three separate signals - Y, Cb/Pb, Cr/Pr.
7.	S-VIDEO terminal
	Connects S-Video output from video equipment to this jack.

8.DC 5V terminal

9.DC 12V TRIGGER terminal

10. COMPONENT VIDEO 2 terminals

Analog/digital video interface transmits via three separate signals - Y, Cb/Pb, Cr/Pr. 11. COMPOSITE VIDEO terminal

Connects composite video output from video equipment to this jack.

Introduction

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

1. POWER
Power On: Discrete power on key.
Power Off: Discrete power off key.	ENG

2.MENU

Opens and Exits the on-screen menu.

3.COLOR TEMP

Selections of color shading. Browse through factory defaults and user color temp.

Image 7

Contents Precision by ViewSonic Compliance Information For Your Records Declaration of RoHS ComplianceCopyright Information Product RegistrationIntroduction InstallationRemote Control Compliance InformationPackage Contents Projector FeaturesIntroduction Control Panel Projector OverviewColor Temp Connection ports Remote ControlPower MenuZOOM/FOCUS Input SelectLight Lens ShiftRemote Control Operation Installing the BatteriesHdmi InstallationPower connection Audio and Video Devices Connectivity ConfigurationInstallation Pro8100 RGB Adjusting the Projected Image Projection Screen Selection Adjusting Projection Image SizePower Light Remote Control direct accessOFF Zoom and Focus Lens ShiftPicture Modes Aspect RatioPCS OFF Color TemperaturePCS Precision Color System PCS onHQV OFF Black LevelHQV HQV onInput Select Daylight SensorDirect Input Keys Remote Control direct access Advanced Operation OSD Menu Main Menu Setup MenuBasic Sub-Menu Picture Sub-MenuPosition 75 Color Temperature Sub-Menu Image Adjust Sub-MenuPhase Position 71Manual OverscanKeystone Geometry Adjust Advanced Sub-MenuAuto Auto V.KEYSTONE OFF LOW MID High Blacker than Black Picture ModeLTI OFF CTI 3 HQVEnhancement TNR MNR BAR OFF Noise ReductionRGB Color Space Config Sub-MenuAuto Projector Settings Location Timeout Transparency TypeTimeout 30 2 OSD LanguagesHigh Altitude TimersAuto Iris OFF Auto Iris PCS Settings Sub-MenuUser 1 PCSPCS Display User PCS OFFColor Flesh tone Edge EnhancementColor Gamma Correction6 3D Color Management Green Enhance Blue Cyan Magenta YellowCustom Color Memory Settings Sub-MenuLoad Green Gain Blue Gain RED Offset Green Offset Blue Offset Custom Color TemperatureLoad SaveLoad SaveSystem Status Screen ResetMENU/EXIT Daylight sensor status Indication if System temperature status, display if system Making Adjustments User Picture Mode Adjustments Making and Recalling the User AdjustmentsUser Color Temperature Adjustments Recalling the User Picture Mode & Color Temperature User PCS AdjustmentsRecalling Both User Picture Mode and User PCS Custom 1 Recalling the User PCS AdjustmentsMaking and Recalling the User Adjustments Appendix Replacing the Lamp AppendixList of Compatible Signals TroubleshootingWSXGA+ SXGA+Uxga Product Specification LED Indicator MessageHDMI-1 RS232 command codeHDMI-2 Key-Pad & IR command Command Send String HEX Complete IR command code table Remote control codeCountry/Region Web Site =Telephone Mail =Fax Customer SupportLimitation of implied warranties