Vidikron Vision 140, Vision 150 operation manual Code Description Power and Cooling

Page 102

Maintenance and Troubleshooting

Table 5-2. Vision 140/150 Error Codes (continued)

Code	Description

	Power and Cooling

46	Red DMD heat sink overheated.

47	Green DMD heat sink overheated.

48	Blue DMD heat sink overheated.

49	Prism overheated.

4C	Projector shutdown due to critical error.

C0	Lamp blower failure (lamp not turned on).

51	LVPS fan failed (Fan 1).

52	LVPS/Red cooling fan failed (Fan 2).

53	DC lamp fan failed (Vision 140; Fan 3).

54	Red DMD heatsink fan failed (Fan 4).

55	Green DMD heatsink fan failed (Fan 5).

56	Blue DMD heatsink fan failed (Fan 6).

57	TIPM fan failed (Fan 7).

58	TIPM fan failed (Fan 8).

Note: To clear a system error, press the EXIT key (on the projector’s rear-panel keypad) twice. If necessary, reset the projector by powering it off, allowing it to cool and powering it on again. Contact your Vidikron dealer or Vidikron technical support if the error persists.

88	Vision Model 140/150 Installation/Operation Manual

Image 102

Contents 140/150 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents Xii 1List of Figures List of Figures About This Manual Carriage return must be used after each command or string1Introduction This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories 2Controls and Functions Vision 140/150 at a GlanceInput Panel Adjustable FeetTOP IR Sensor BUILT-IN Keypad LED Status DisplayEthernet Vision 140/150 Input PanelRemote Input 1 RgbhvVision 140/150 Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonVHD Controller Front Panel IR SensorVacuum Fluorescent Display Inputs VHD Controller Rear PanelHdmi OUT Composite Video InputRS-232 Control Port Power Input 100 to 240 VACMain Power Switch Main AC FuseVision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote ControlIR Output Indicator LightRETURN/EXIT ISF DAY CinemaControls and Functions To install batteries in the remote control 3InstallationRemote Control OperationInstallation Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsWith 126.9x54-inch Vision 140/150 Lens Options and Throw RatiosThrow Ratio ScreenPosition Ceiling InstallationFloor Installation Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled atLens motor installed Ceiling-mounting an AutoScope-equipped projectorFloor-Mount Floor Mounting Upright Adjusting the ProjectionMounting the Vision 140/150 AngleConnecting the VHD Connections to the Vision 140/150 and VHD Controller140/150 Connecting Source Hdmi Connections See FigureController Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 14. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentConnecting an External IR Receiver to the VHD Controller Power sourceProjector Turning on the Power Component SD Ntsc 480i 169 V150Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Plate fixed CineWideHorizontal Position X Adjustment Installation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 MainControl Functions Disabled Navigating the Projector4x3 night Vhd 720p16x9 night Ltrbox nightAuto Source Locked Previous Channel Next Channel Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu InterlaceNative aspect ratio is with the primary lens only. With an SupportSize and Position Menu Installation Adjust Pixel Tracking before Pixel Phase Picture Quality MenuTechnicians use the White Balance submenu Internal grayscale test patternThere must be at least two consecutive white pixels present Uncheck this item before exiting this menuPre Calibration Red Black Level Back Porch Clipping Detector Color Enable RedAuto Color Enable Clamping Red White LevelInstallation Menu LumaCal lamp calibration takes approximately two minutesAbove, the Automatic Lens Calibration setting has no effect Working With the Lamp FactorsValue only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages Installation Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioMain Menu Input SourceAspect Ratio 169 Aspect Ratio SettingsDescription Hdtv programs in theirRemote With a 2.351 screen and aPerform the adjustments in the order listed here PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF NightOperation Service You must enter a passcode to access the Service menuDo not change the Type setting in this menu Vertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation 5Maintenance and Troubleshooting Lamp and Filter ReplacementLamp cover 2 screws Removing the Lamp RVR Lens Replacement Removing the Primary Lens Troubleshooting Tips Troubleshooting Chart Symptom Possible Causes Solution Symptom Trigger CineWide withVision 140/150 Error Codes Description GeneralLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Command Value Stored? Description Miscellaneous CommandsEnter key Serial Communications 7Specifications Vision 140/150 SpecificationsVision 140/150 Specifications Power Requirements Vision Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage 020-0833-01 Rev. a March