Vidikron Vision 140 Installing and Adjusting the CineWide Anamorphic Lens, Plate fixed CineWide

Page 54

Installation

3.11

Installing and Adjusting the CineWide Anamorphic Lens

If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the anamorphic lens. Note that some components shipped with your projector may differ slightly from what is shown in these instructions.

It is extremely important that the primary lens is properly adjusted

Note before you install the anamorphic lens. Ensure that the 16:9 or 4:3 image from the primary lens is perfectly centered on the screen.

Attach Lens Mounting ➤ 1.

Remove the two Z-Adjustment Levers and 1/4-20 Fiber Washers from the bottom of the

Assembly to Lens Motor

lens mounting assembly.

Carriage Plate (CineWide

2.

Place the Lens Mounting Assembly on top of (or under, if the projector is inverted) the

with AutoScope) or Base

Lens Motor Carriage Plate or Base Plate, so that the two threaded posts at the bottom of

Plate (fixed CineWide)

the Z-Adjustment Plate pass through the corresponding slots on the carriage plate or

base plate.

3.

Secure the Lens Mounting Assembly to the plate with the Z-Adjustment Levers and

Washers that you removed in Step 1.

40	Vision Model 140/150 Installation/Operation Manual

Image 54

Contents 140/150 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsTable of Contents Xii 1List of Figures List of Figures About This Manual Carriage return must be used after each command or string1Introduction This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories 2Controls and Functions Vision 140/150 at a GlanceInput Panel Adjustable FeetTOP IR Sensor BUILT-IN Keypad LED Status DisplayEthernet Vision 140/150 Input PanelRemote Input 1 RgbhvVision 140/150 Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonVHD Controller Front Panel IR SensorVacuum Fluorescent Display Inputs VHD Controller Rear PanelHdmi OUT Composite Video InputRS-232 Control Port Power Input 100 to 240 VACMain Power Switch Main AC FuseVision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote ControlIR Output Indicator LightRETURN/EXIT ISF DAY CinemaControls and Functions To install batteries in the remote control 3InstallationRemote Control OperationInstallation Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsWith 126.9x54-inch Vision 140/150 Lens Options and Throw RatiosThrow Ratio ScreenPosition Ceiling InstallationFloor Installation Vertical and Horizontal LensHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled atLens motor installed Ceiling-mounting an AutoScope-equipped projectorFloor-Mount Floor Mounting Upright Adjusting the ProjectionMounting the Vision 140/150 AngleConnecting the VHD Connections to the Vision 140/150 and VHD Controller140/150 Connecting Source Hdmi Connections See FigureController Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 14. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentConnecting an External IR Receiver to the VHD Controller Power sourceProjector Turning on the Power Component SD Ntsc 480i 169 V150Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Plate fixed CineWideHorizontal Position X Adjustment Installation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 MainControl Functions Disabled Navigating the Projector4x3 night Vhd 720p16x9 night Ltrbox nightAuto Source Locked Previous Channel Next Channel Name 16x9 nightNumber Sync 26.97 kHz Input 23.98 Hz Menu InterlaceNative aspect ratio is with the primary lens only. With an SupportSize and Position Menu Installation Adjust Pixel Tracking before Pixel Phase Picture Quality MenuTechnicians use the White Balance submenu Internal grayscale test patternThere must be at least two consecutive white pixels present Uncheck this item before exiting this menuPre Calibration Red Black Level Back Porch Clipping Detector Color Enable RedAuto Color Enable Clamping Red White LevelInstallation Menu LumaCal lamp calibration takes approximately two minutesAbove, the Automatic Lens Calibration setting has no effect Working With the Lamp FactorsValue only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages Installation Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioMain Menu Input SourceAspect Ratio 169 Aspect Ratio SettingsDescription Hdtv programs in theirRemote With a 2.351 screen and aPerform the adjustments in the order listed here PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationShould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration ISF NightOperation Service You must enter a passcode to access the Service menuDo not change the Type setting in this menu Vertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation 5Maintenance and Troubleshooting Lamp and Filter ReplacementLamp cover 2 screws Removing the Lamp RVR Lens Replacement Removing the Primary LensTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Symptom Trigger CineWide withVision 140/150 Error Codes Description GeneralLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Multiple serial commandsAspect Ratio Commands Image Preset Commands Output Shift Commands Command Value Stored? Description Miscellaneous CommandsEnter key Serial Communications 7Specifications Vision 140/150 SpecificationsVision 140/150 Specifications Power Requirements Vision Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage 020-0833-01 Rev. a March

Vision 140, Vision 150 specifications

The Vidikron Vision 150 and Vision 140 are two exceptional high-definition home theater projectors that have garnered attention for their impressive performance and innovative features. Designed for cinema enthusiasts, these models bring the big screen experience into the comfort of one’s living room, delivering outstanding picture quality and an immersive viewing experience.

At the heart of the Vidikron Vision series is a state-of-the-art DLP (Digital Light Processing) projection technology which provides sharp images and vibrant colors. Both projectors utilize a high-contrast 1080p resolution, ensuring that content looks lifelike and detailed. The Vision 150, particularly, stands out for its ability to reproduce deep blacks and luminous whites, thanks to its advanced dynamic iris functionality, which optimizes light output in real time.

One of the standout features of the Vision 150 is its color accuracy, achieved through a specialized color management system. This system enhances the projector's capability to reproduce various color gamuts, allowing users to experience films, sports, and games exactly as the content creators intended. The Vision 140, while slightly less feature-rich, still offers remarkable color fidelity, making it a strong competitor in the mid-range projector market.

Both models boast a generous array of connectivity options, accommodating various devices effortlessly. Each projector is equipped with multiple HDMI ports, component video inputs, and RS-232 connections, facilitating seamless integration with home theater systems. This versatility ensures that users can easily switch between gaming consoles, Blu-ray players, and streaming devices without hassle.

The Vidikron Vision projectors also feature efficient cooling systems, designed for quiet operation without compromising performance. This aspect is particularly vital during long movie marathons or intense gaming sessions, allowing users to immerse themselves in content without distractions from fan noise.

In terms of installation, both models are relatively user-friendly, featuring lens shift and zoom capabilities that facilitate flexible placement options. This allows for optimal image size and position depending on the dimensions of the viewing room.

In summary, the Vidikron Vision 150 and Vision 140 projectors represent a perfect blend of cutting-edge technology, stunning visuals, and user-friendly functionality. Their commitment to color accuracy and detailed imagery makes them a top choice for those seeking an enthralling home cinema experience. Whether it’s for movie nights with family or gaming marathons with friends, these projectors are poised to elevate any home entertainment setup.